Q4/ Compute the flow rate of water through the 3 pipes connected in series as shownIn the Figure below. Let f= 0.016 and neglect minor losses.Pipe No.Diameter of Piped(mm)300200250123Water20 ftLenth of PipeL(m)335040150 ft. 8-in diameter120 ft, 10-in diameter100 ft, 12-in diameterWaterFig. 10-2

Answered: Image /qna-images/answer/cc58b408-1772-479e-b4b1-15bdd918291c.jpg

Q4/ Compute the flow rate of water through the 3 pipes connected in series as shown In the Figure below. Let f= 0.016 and neglect minor losses. Pipe No. 1 2 23 3 Water 20 ft Lenth of Pipe Diameter of Pipe L (m) 33 50 40 150 ft, 8-in diameter 120 ft, 10-in diameter d (mm) 300 200 250 100 ft, 12-in diameter Water Fig. 10-2

Q4/ Compute the flow rate of water through the 3 pipes connected in series as shown In the Figure below. Let f= 0.016 and neglect minor losses. Pipe No. 1 2 23 3 Water 20 ft Lenth of Pipe Diameter of Pipe L (m) 33 50 40 150 ft, 8-in diameter 120 ft, 10-in diameter d (mm) 300 200 250 100 ft, 12-in diameter Water Fig. 10-2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The water flow of 35,000 Liters/min was developed into a booster station with a pump installed rated as follows: Pressure at Discharge side= 4.18 bars, 850mm above the pump C.L Suction Pressure= 220mmHg vacuum , 425mm below the pump C.L Pipe Dia @ suction=16 inches and Pipe Dia @ Discharge 12 ½ inches. 1. Draw the illustrative diagram 2. Calculate the Head at discharge, Velocity Head, Elevation Head and the Total Head of the Pump.
13 PLEASE PROVIDE COMPLETE AND DETAILED SOLUTION
In the figure shown pipes are in parallel connection with properties given. If the flow into the system is 850lps with total head loss of 10 J/N. For the value of f=0.020 for all pipes, find the diameter of pipe 4. Pipe No. Length - m Diameter - em 1 1000 90 500 50 3 600 40 4 800 5 700 75
In the illustration: A В 2 D All friction factor f - 0.02 All pipe lengths L- 250m Diameter of Pipe A= 400mm with Flow Rate at Pipe A = 700 L/s Diameter of Pipe B = 300mm Diameter of Pipe C = 200mm Diameter of Pipe D = 400mm Solve for - difference in elevation in meters in between reservoirs.
The suction side of a pipe system is as shown in the figure. The pump discharges 495 gpm of water under a total head of 100 ft at 40°F. Atmospheric pressure = 32.7 ft of water. If the required NPSH is 9 ft, will there be a cavitation problem? Please note that 1 cfs equals 449 gpm. 12 ft 6 ft Diameter L = 300 ft Steel = 10 in 5
In the pipe systems (a), (b), and (c) in the Figure, find the flow and velocity in each pipe and the pressure at points A. Assume all nodes are at identical elevations. m/min 20 m/min 20 m /min P- 1000 kP Sm/min 1500 m 1000 m 455 mm 405 mm 1000 m 405 mm 800 m 255 mm 300 m305 mm 300 m 205 men 1100 m 305 mm 1000 m 305 mm A500 m 205 mm 10 m/min 5m/min 10m3/min 5 m/min 15 m /min 5m/min Elev 300 m 405 mm 2000 m 150 2000 m Elev 250 m 5m/min 10 im/min 6 m/min 205 mm 205 mm 2000 m A 2000 m le) 000
Determine the flow distribution of water in the system shown in Figure below. Assume constant friction factors, with f= 0.03. The head-discharge for the pump is Hp = 70 m el 50 m Pipe L (m) D (mm) ΣΚ el 48 m 1 100 750 850 350 200 200 [2] [4] 3 el 0m [5] 4 500 200 350 250 [1] [3]
The circular water pipes shown in the sketch are following full. The velocity of flow (in m/s) in the branch pipe "R" is V = 6 m/s dia = 4 m – મ N=? R V = 5 m/s dia= 2 m
The circular water pipes shown in the sketch are flowing full. The velocity of flow (in m/s) in the branch pipe "R" is PI V = 6m/s, dia = 4m - = V = ? R Q V = 5m/s dia = 2m
Find the head loss in the pipe using Darcy Weisbach, Manning and Hazen Williams (remember to watch units and make sure you account for the pipe length). If they are different, discuss why they might be different. The following are relevant: L (m) D (m) T Pipe Q (m^3/s) 4000 0.25 20 C new Cl 0.1
P10.) Determine the flow in each pipe shown in the figure. Assume f = 0.02 for all pipes. Subject: fluid mechanic Lesson: *Conservation of Energy *Fluid Flow in Pipes
2. The total flow from A to E is 300 L/s. Compute the flow for pipes 2, 3, 4, and 5 3 5 D 6 Pipe 1 2 3 4 5 6 f 0.02 0.02 0.02 0.02 0.02 0.02 Diameter Length (mm) in (m) 450 400 250 360 200 600 300 1400 250 450 300 700