(Q3) Calculate the total solar irradiation on vertical wall facing a direction 45° south of the east in a location with a latitude of 22° N at 11:00 am solar time on 1 June. Assume clear sky conditions and the ground reflectivity is 0.6. Also determine the sunrise and sunset solar times. Show all calculations and results and highlight the result of each calculation for clarity.

(Q3) Calculate the total solar irradiation on vertical wall facing a direction 45° south of the east in a location with a latitude of 22° N at 11:00 am solar time on 1 June. Assume clear sky conditions and the ground reflectivity is 0.6. Also determine the sunrise and sunset solar times. Show all calculations and results and highlight the result of each calculation for clarity.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.26P: 1.26 Repeat Problem 1.25 but assume that the surface of the storage vessel has an absorbance (equal...

See similar textbooks

Similar questions

A tungsten filament is heated to 2700 K. At what wavelength is the maximum amount of radiation emitted? What fraction of the total energy is in the visible range (0.4to0.75m)? Assume that the filament radiates as a graybody.
1.26 Repeat Problem 1.25 but assume that the surface of the storage vessel has an absorbance (equal to the emittance) of 0.1. Then determine the rate of evaporation of the liquid oxygen in kilograms per second and pounds per hour, assuming that convection can be neglected. The heat of vaporization of oxygen at –183°C is .
11.31 A large slab of steel 0.1 m thick contains a 0.1 -m-di- ameter circular hole whose axis is normal to the surface. Considering the sides of the hole to be black, specify the rate of radiative heat loss from the hole. The plate is at 811 K, and the surroundings are at 300 K.
At 40º north latitude, on 22 December, array collectors are required to see direct sunlight for at least 4 hours a day. Since the collector lengths are 1.3 m and the tilt angles are 55º, what should be the minimum distance between the collectors.
An industrial engineer designed a workstation where the seeing task was difficult because of the size of the components going into the assembly. The desired brightness was 150 foot Lamberts and the workstation was painted a medium green having a reflectance of 52%. fc (Please keep as an integer) (2) By referring to the table in slide 7 (lecture 5), please estimate the required illumination if you repainted the workstation with a light cream paint: (1) What illumination would be required at this workstation to provide the desired brightness ? fc (Please keep as an integer)
Need detailed Solution ,Previous One not enough. 1) For two surfaces, labelled 1 and 2, the view factor F_12 is 0.4. Surface 2 has twice the area of surface 1, what is the view factor from surface 2 to surface 1?
A typical car's exterior consists of a thin layer of silica (SiO2) over an opaque painted metal panel. Silica is transparent in the visible wavelengths but offers high reflectance in the near- to mid- infrared wavelengths. The plot on the next page depicts the diffuse spectral reflectivity (pa) of the car's surface: Spectral reflectivity, P₂ 0.8 0.6 0.4 ལ 0.2 0 0.1 1 1 10 Wavelength, λ(μm) 100 If the car's exterior temperature is T₁ = 77°C, determine both the total absorptivity (a) and the total emissivity (a) of the silica-covered panel. Assume that the Sun's temperature is Tsun = 5800 K.
2. An UV stepper (Exposure Machine) has a NA numerical aperture of 0.3 and uses a light source with a wavelength of 436nm. What is the minimum feature size you would expect the stepper to be able to produce? What would be the maximum thickness of resist that the stepper could successfully expose?
An IE has designed a workstation in the Electronics Company where the seeing task was difficult due to the scale of the components going into the assembly. The target brightness was 100fL and a medium green with a reflection of 50 per cent was painted at the workstation. What illumination would be needed in foot candles to provide the desired brightness at this workstation? * 200 foot candle O 100 foot candle O 300 foot candle O 250 foot candle
You want to have an illuminance of 300 lux on Mrs. Pott (under the SPOTLIGHT#1). What is the Luminous Flux (lumen) the lamp need to releases assuming homogeneous distribution of the light in the illuminated circle?
Calculate the absorbed irradiation by the surface in W/m2
Problem 4 Emissivity/Absorptivity 0.8 30.6 ་ A white paint that can be used for passive radiative (b) 1 cooling under the Sun. Provided the following simplified spectral absorptivity/emissivity plot (α) or &) on the right, calculate the net radiative heat flux qrad from a uniform-temperature painted surface at Ts=300 K. The Sun's irradiation on Earth is Gsun 1380 W/m² and its blackbody temperature is Tsun = 5800 K. Ignore the radiation from the atmosphere (surroundings). 0.2 0 ° 3 5 DO Wavelength (um)