The following cireuit is part of an audio systan , If we wont to transfer max pawer to the 8S vesistore find the value of Rp to that max pauer trens terence. get . 300 N + vT 10 kN 70 kM 3 × 10-³v7 RE

Q: Thevenin and Norton Equivalent: 15). For the circuit in Fig. 4.109, find Thevenin equivalent between…

A: We need to find out thevenin equivalent circuit and norton equivalent circuit

Q: What is external setup?

A: EXTERNAL SETUP: Setup is the method involved with setting up a machine to run an item. A portion of…

Q: i) a) What is the use of A.C and D.C bridges in measurement system? b) Draw the schematic diagram of…

A:

Q: Explain briefly, the Professional Code of Ethics of an Electrical Engineer.

A:

Q: Q3 put "T" in front of true sentence &"F" in front of the false sentence. A. In differently compound…

A: Solution

Q: How many nodes are there? image d.png ... 1.5 0 20 50 2 A( )5 A Answer _nodes

A:

Q: On Tuesday I .( have) lunch with some girlfriends * Your answer Oh ! interesting ! what ..you...…

A: Given sentences, On Tuesday I ........ (have) lunch with some girlfriends Oh ! interesting ! what…

Q: Explain the gaurd band

A: A guard band is a narrow frequency range that separates two ranges of wider frequency. This provides…

Q: The curent in a 0.05-H inductor is I= 42 – 30° A. If the frequency of the current is 60 Hz, what is…

A: The equation of the current in time domain is: I(t)=4cos(ωt-300)A The inductor value is L = 0.05H…

Q: Test 2: Modified true or false:Shade letter A if the first statement is True, Shade Letter B if the…

A: The given statements are as follows, 1. The passing general average rating shall be seventy percent…

Q: Develop a LabVIEW code (Front panel and Block diagram) of a wire cutting system

A: LabVIEW code for a wire cutting system. However, please note that without specific requirements or…

Q: 12. To read and understand electrical blueprints, you need to know A. how to sketch a plan view.…

A: Given To specify What is important to read and understand electrical blue prints.

Q: Q3) Machines A and B make components, which are then placed on a conveyor belt. Of those made by…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: A power generation plant connected to bulk load of high voltage industries shown in Figure Q3 has…

A:

Q: eir mother was (cooking dinner) wl .he pho ho was cooking dinner when he

A: Mother is cooking dinner when he phoned.

Q: a) Draw the block diagram of a measurement system.

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: device has a ... rogrammable AND array and fixed .connections for the OR array PROM O PLA O

A:

Q: An engineer spends about …………………….….. percent of his/her time writing.   Select one: a. 70 b. 10…

A: Solution: In every engineers engineering career, they spend much time on theoritical knowledge and…

Q: ) current signs determined?: (b) voltage signs determined

A:

Q: In the circuit below I = 3245° mA. What is the KCL expression at node a following the %3D…

A:

Q: How equation is obtained ? is that equation given in the textbook ?

A: That equation is the direct formula of pulse spread. And no need of derivation of the equation.…

Q: What are the answers for a) & b)?...

A: (a) Power is given, Voltage is given, Current is given, For three phase circuit power is given by,

Q: All forms of communication have a(n)_ built into them. O A. bias O B. Mercator projection

A: Communication System- The communication system model is described as a communication exchange…

Q: P-channel MOSFET is basically a following device. a. voltage operated O b. low-frequency operated O…

A: MOSFET is controlled by the application of GATE pulse .  GATE pulse controls the conduction state of…

Q: Describe the job of the Board of Electrical Engineering in one sentence.

A: The solution is given

Q: Q6) Explain by drawing a block diagram of a power supply?

A: Draw the block diagram of the Regulated power supply.

Q: As an electrical engineer, what are the fields of work in this specialization?

A: As electrical engineer there are various specialization field are available over the world wide.…

Q: A Class II hazardous location is where_ Select one: Oa. gasses are present Ob. combustible dust is…

A: We need to select correct option for given statement.

Q: 5- An instrument is used for lowering the value of voltage for measuring and protection is a.…

A: The objective is to determine the correct option for the given statements.

Q: D: has been eaten

A: Answer According to given information

Q: If the L[ eat cos5t] = (s-a)/( s² - bs + 48), determine the value of a.

A: It is given that: Leatcos5t=s-as2-bs+48

Q: A telecom company asks you to design a cable for an optical communication system. Which principle of…

A: Given: A telecom company asks you to design a cable for an optical communication system. To find:…

Q: Explain Transducer classification adding EXAMPLE to each category.

A: Transducer - A transducer is a machine that, when activated, converts one form of energy to another.…

Q: Facts: You have learned the basics and fundamentals of Electronics. We could say that all of the…

A: These are three component which are used in every circuit 1. Capacitor 2.Resistor 3. Diode

Q: Fill the following blanks in the sub-program with suitable numbers to generate 7 sec delay.

A: Explanation:The outer loop (D2) is initialized with a count of 7 to achieve a 7-second delay.The…

Q: What Is a function of a capacity

A: