Q2/A solid circular transmission shaft of (2m) long with angle of twist not exceed (39) which used to transmit power of (2.5 h.p) at speed of (46 r.p.m). Determine the required diameter of the shaft if knowing that the shaft made of :- 1-Steel with allowable shearing stress of (90MPa) and modulus of rigidity of (77GPa). 2- Bronze with allowable shearing stress of (35MPa) and modulus of rigidity of (42GPa).

Q2/A solid circular transmission shaft of (2m) long with angle of twist not exceed (39) which used to transmit power of (2.5 h.p) at speed of (46 r.p.m). Determine the required diameter of the shaft if knowing that the shaft made of :- 1-Steel with allowable shearing stress of (90MPa) and modulus of rigidity of (77GPa). 2- Bronze with allowable shearing stress of (35MPa) and modulus of rigidity of (42GPa).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A composite shaft is made of slipping a bronze tube of 3-in. outer diameter and 2-in. inner diameter over a solid steel shaft of the same length and 2-in. diameter. The two components are fastened rigidly together at their ends. What is the largest torque that can be carried by the composite shaft if the working shear stresses are 10 ksi for bronze and 14 ksi for the steel? If the hollow tube is made out of steel and the solid shaft is made out of bronze, what is the largest torque that can be carried by the composite shaft if the same working shear stresses are applied? For bronze, G = 6 x 10° psi, and for steel, G = 12 x 10°.
Figure 1 is presented the solid shaft AB rotates at 650 rpm and transmits 30 kW from the motor machine tools connected to gears F and G. Assuming that, 10 kW is taken off at gear F and 20 k taken off at gear G, knowing that allowable torsional shear stress is equal to (65 plus last digit of student ID) MPa. Design the smallest permissible diameter of shaft AB. Figure 1 150 mm 225 mm 905 mm 150 mm 60 mm 100 mm D. 60 mm B.
Select the size of a hollow steel shaft necessary to transmit 150 hp at 250 rpm without exceeding an allowable shear stress of 7.4 ksi, or having a relative angle of twist beyond an allowable value of 0.35 degrees per 1-ft length. The ratio k-d,/d,=0.75
Q.4. A solid steel shaft 5m long is stressed to 80 MPa when twisted through 4 degrees using G 83 GPa. Determine the shaft diameter and what power can be transmitted by the shaft at 1200 rpm.
Q: For the aluminum shaft shown (G 27 GPa), determine (a) the torque T that causes an angle of twist of 4° (b) the angle of twist caused by the same torque T in a solid cylindrical shaft of the same length and cross-sectional area. 1.25 m 18 mm 12 mm
A solid shaft in a rolling mill transmits 20 kW at 2 revolutions per second. The length of the shaft is 3 m and modulus of rigidity is 83,000 MPa. Which of the following gives the torque carried by the shaft?a. 1.59 kN-m c. 2.69 kN-mb. 3.45 kN-m d. 4.81 kN-m Which of the following gives the minimum diameter so that the allowable torsional shearing of 40 MPa will not beexceeded?a. 88 mm c. 59 mmb. 45 mm d. 76 mm Which of the following gives the minimum diameter so that the allowable angle of twist of 6O will not be exceeded?a. 29 mm c. 35 mmb. 49 mm d. 55 mm
The motor on the left provides a torque of 5500 N•m to the gear shaft shown. The motor runs machines connected to gears B, C and D requiring torques of 3000 N•m, 1500 N•m and 1000 N•m respectively. A, B, C and D are spaced 2000 mm apart and the diameter of the shaft is 75 mm. The shear modulus of the shaft material is 80x109 N/m2. Determine: Minimum diameter required (in millimeters) if the shearing stress in the shaft is limited to 100x106 N/m2 Rotation of D with respect to A Note: Draw the Free Body Diagram, Compute for all of the necessary elements, Include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
1. The endurance limit for rotating shaft, if its ultimate strength Su=1600 Mpa is:
A solid 2.9-in.-diameter bronze [ G = 7100 ksi] shaft is 8-ft long. The allowable shear stress in the shaft is 10.2 ksi and the angle of twist must not exceed 0.034 rad. Determine the maximum horsepower P that this shaft can deliver: (a) when rotating at 182 rpm. (b) when rotating at 644 rpm.
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
Design a hallow shaft (Diameter and length) that develops 80 kW of power while rotating at a speed of 4000 rpm. The design constrains are as under:The angle of twist not to exceed 0.200Shear stress is not to exceed 480 MN/m2The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m2.
a) A solid alloy shaft 5cm diameter is to be coupled in series with a hollow steel shaft ofthe same external diameter. Find the internal diameter of the steel shaft if the angle oftwist per unit length is to be 75% of that of the alloy shaft. Determine the speed at whichthe shafts are to be driven to transmit 200kW, if the limits of shearing stress are to be55N/mm2 and 75N/mm2 in alloy and steel respectively. Gsteel = 2.2Galloy