Q21. What is the drive output frequency when switch S1 only is closed and the analog inputsare connected to a potentiometer set to its 80% maximum position (8V analog input)?Asume that the potentiometer allows for a speed range from zero speed to maximum(70Hz) speed as the input voltage ranges from 0V to 10V.(a) 18 Hz(b) 35 Hz(c) 52 Hz(d) 56 Hz(e) 70 HzQ22. What is the drive output frequency when switches S1, S4, S5 and S6 only are closed?(a) 72 Hz(b) 70 Hz(c) 68 Hz(d) 65 Hz(e) 55 HzQ23. Which switch (closed) combination will produce an output frequency of 50 Hz andreverse rotation?(a) S2 and S4(b) S2 and S6(c) S2, S4 and S5(d) S2, S5 and S6(e) S2, S4 and S6 Q18-Q25 refer to the figure below:Logic input assignmentsLIIForwardL12ReverseL13DC injection brakingL142 preset speedsLIS4 preset speedsLI68 preset speedsPreselected speeds settingsSP2Hz25SP3Hz30SP4Hz35SP5Hz40SP6Hz45SP7Hz50SP8HzSP9Hz5560OPWR+24TFR Max. outputfrequencyLSP Low speedHSP High speedHzHzHzWiring schematic599 399S2S3 S4 S5 S6TCC 2/370.015.065.0

According to the question, for the given wiring schematic as shown below We need to find the…

Q21. What is the drive output frequency when switch S1 only is closed and the analog inputs are connected to a potentiometer set to its 80% maximum position (8V analog input)? Asume that the potentiometer allows for a speed range from zero speed to maximum (70Hz) speed as the input voltage ranges from 0V to 10V. (a) 18 Hz (b) 35 Hz (c) 52 Hz (d) 56 Hz (e) 70 Hz Q22. What is the drive output frequency when switches S1, S4, S5 and S6 only are closed?

Q21. What is the drive output frequency when switch S1 only is closed and the analog inputs are connected to a potentiometer set to its 80% maximum position (8V analog input)? Asume that the potentiometer allows for a speed range from zero speed to maximum (70Hz) speed as the input voltage ranges from 0V to 10V. (a) 18 Hz (b) 35 Hz (c) 52 Hz (d) 56 Hz (e) 70 Hz Q22. What is the drive output frequency when switches S1, S4, S5 and S6 only are closed?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the LAD for the silo simulator in Logix pro
A 120 Vp is applied to the primary coil of a center-tap transformer of turn ratio (n1 : n2 = 6: 2) . If the secondary coils are connected to a Ge diodes center-tap full wave rectifier, the output DC voltage is about __________. *1- 13.42 V2- 14.15 V3- 15.58 V4-12.54 V5- 16.23 V
Kp controller is a. working on steady state O b. working on transient state O c. frequency independant d. frequency dependant
- In d.c. generators armature reaction is produced by armature current O none of the mentioned compensating winding current field current O commutating winding current The use of d.c. generators elminated the use of rectifiers and ac supplies True False s If the number of layerallot is 4 then the number of colls the number of slots Equal to O none of the mentioned O twice O half O s In 2-pole machines: the wave winding have greater generated voltage than the lap winding'armatures True False For high rotating speed machines the number of poles munt be Little Tiue O Fale O O O
2. Consider the following circuit D å lå a. Find the expressions for D, T, Qo*, Q₁*. b. Write the transition output table. c. Draw the state diagram of the circuit. d. Is this a Mealy or Moore machine? Explain. T 21 a la 1
The p-channel JFET used in Digital technology as_____. a.switch b.rectifier c.invertor d.amplifier
Create a sequence detector that detects the sequence 1001 or 0110 by using Verilog Code. Construct the modules for both the Moore and Mealy models. Demonstrate your simulation results using the following input sequence for the test fixture (test bench): x= 0010011010010110010110110100
Comparing the performance with controlled rectifier circuit which one of the following statement is correct for DC -DC chopper ? O a. Regenerative braking process is very slow O b. Efficiency is poor in chopper circuit O c. small filters are required O d. Switching frequency is not responsible for output ripples
Arduino Mega is based on ATmega328 processor True False O * Arduino Uno has .... Analogue input/output 12 O 8 16 Arduino Uno processor speed is greater than Arduino Due False O True O
I have four ESP-WROOM-32D boards, and four NRF24L01 modules. Each ESP-WROOM-32D board is connected to one NRF24L01 module. I want one NRF24L01 module to send a "Hello" message to the other three NRF24L01 modules at the same time. What is a good starter code in Arduino IDE?
Comparing the performance with controlled rectifier circuit which one of the following statement is wrong for DC -DC chopper ? a. small filters are required O b. Regenerative braking process is very slow O c. Switching frequency is responsible for output ripples O d. Efficiency is better in chopper circuit
By comparing the performance of DC -DC chopper with controlled rectifier circuit which one of the following statement is wrong ? O a. Efficiency is better in chopper circuit b. small filters are required in chopper circuit O c. Regenerative braking process is very slow in chopper circuit O d. Switching frequency is responsible for output ripples in chopper circuit Clear my choice