Q2. Given the circuit configuration below, Vcc=VEE=6v, R = 2kn Rc = 6kN, Re = 5kN, Rb = 0, Rw 2002 where the sliding contact is at the middle of variable resistor. T1 and T2 are with the same characteristics, where B 100, rbe = 5kn. Find out the voltage gain in common mode and differential mode, and compute %3D %3D %3D CMRR. Uo 오 T. UI

Q2. Given the circuit configuration below, Vcc=VEE=6v, R = 2kn Rc = 6kN, Re = 5kN, Rb = 0, Rw 2002 where the sliding contact is at the middle of variable resistor. T1 and T2 are with the same characteristics, where B 100, rbe = 5kn. Find out the voltage gain in common mode and differential mode, and compute %3D %3D %3D CMRR. Uo 오 T. UI

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The controlling parameter in MOSFET is a) Vds b) lg c) Vgs d) Is
Sketch carefully the following signal.in dsp material or signal and system
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
c. For the circuit shown in Figure, determine lc and VCB. Assume the transistor to be made of Silicon. Ic RE=1.6 kn Rc=1.1 kn EE=8 V Vcc= 20 v
Q3) For the regulator circuit shown in figure below, Vin-15 V, Rs-10 2, Vz-9.1 V, VBE=0.8V, and R=40 2. What are the values of output voltage, input current, the load current, and collector current. 102016 2-8594 Vin R$ Ⓡ R₂ Vout
Sketch the de load line, quiescent collector current, quiescent voltsge, input power, output power and maximum efficiency of the circuit shown an Figure. The input results in a base current of 5 mA peak to peak What maximum output power can be delivered by the circuit, if the input voltage is changed resulting in a base current of 10mA peak to peak and hence find the maximum etficiency. cc=15 V R =18 2 -25
In an RC coupled clamping circuit, the relationship of the circuit discharge time constant and the input waveform period a. should be long b. should be short c. does not matter d. is ignored if the RC value is less than one
circuits by using the small signal models of the transistor. Assume the Early voltage of the transistors are infinitely large. Calculate the small-signal input and output impedances of the following Vcc R1 R1 Rout VB RE Rin R2
The output is out-of-phase with the input in a. a common emitter circuit b. a common base circuit c. a common collector circuit d. more than one of the above
Determine VB, VE, VC, VCE, IB, IE, and IC in Figure. The 2N3904 is a general purpose transistor with a typical BDC 200 Vcc +30 V WWII VCE VB R₁ • 22 ΚΩ IC(mA) Chọn... * Chọn... * IB(UA) Chọn... * IE(MA) Chọn... ◆ Chọn... * Chọn... * Chọn... * VE VC R₂ ´ 10 ΚΩ www Rc 1.0 ΚΩ 2N3904 PDC=200 RE 1.0 ΚΩ
c) A buck converter with constant frequency peak current mode control has Vs = 28V, V = 20V, L = 301uH, fs = 100 kHz. Find the ramp slop for the optimum compensation and the peak compensation voltage. %3D
The arrow on the symbol of MOSFET indicates O a. that it is a N-channel MOSFET O b. the direction of conventional current flow O c. that it is a P-channel MOSFET O d. the direction of electrons