Q2: Water flows through a tube with a diameter of A (mm), and ends with a nozzle in the form of a horizontal bend, changing the direction of flow at an angle of 30°, as shown in the figure, so if the rate of water flow is B (m'/s) out into the atmosphere from the end of the mouth with a diameter of C (mm), determine the vector Horizontal net force required to hold the tube bend in place. C.V

Q2: Water flows through a tube with a diameter of A (mm), and ends with a nozzle in the form of a horizontal bend, changing the direction of flow at an angle of 30°, as shown in the figure, so if the rate of water flow is B (m'/s) out into the atmosphere from the end of the mouth with a diameter of C (mm), determine the vector Horizontal net force required to hold the tube bend in place. C.V

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

115 m turbine 2 In the above example problem, a hydroelectric turbine at the base of a dam is shown schematically. The height of the water above the turbine station given as 115 m. This turbine produces 4.6 MW of electricity, and you may assume the losses in the system to be equivalent to 10 m of head of water. The diameter of the pipe at the turbine exit is 0.75 m, and the velocity of water exiting from the pipe is 12.5 m/s. Caleulate the efficiency of the turbine.
Water at a pressure of 294 3 kN/m flows through a horizontal pipe of 100 mm diameter with a velocity of 2 m/s. If the diameter of the pipe gradually reduces to 50 mm, what is the axial force on the pipe assuming no loss of energy.
answer fast
Q6: The U-bend in the figure below is connected to a flow system by flexible hoses that transmit no force. The pipe has an ID of 3 in. Water is flowing through the pipe at a rate of 600 gal/min and density is 1000 kg/m³. The pressure at point 1 to 5 psig and at point 2 is 3 psig. What is the vertical component of the force in the support? Neglect the weight of the pipe and fluid. Flow FIGURE Vertical pipe U-bend. Flex hoses Support
A room has a volume of 349 m3. An air-conditioning system is to replace the air in this room every 81.5 minutes, using ducts that have a square cross section. Assuming that air can be treated as an incompressible fluid, find the length of a side of the square if the air speed within the ducts is (a) 2.00 m/s and (b) 7.00 m/s. a: b:
A tank (contains a fluid of density=1239.6 kg/m3) stands on a frictionless cart (The cart is fixed) and feeds a jet of diameter 4 cm and velocity 6 m/s, which is deflected 0=35 degree by a vane. Compute the tension in the supporting cable. 6 m/s 35 deg -D= 4 m- Do = 4 cm Cable
Imagine the water level in the tank as shown in the Figure rises at a rate of 0.004579 ft³/sec. then find: i) The volume flowrate of water leaving the tank (Q3) in ft³/s from pipe 3. ii) The average velocity of water leaving the tank (V3) in ft/s from pipe 3. Pipe 1: Qi=0.0109 ft²/s Pipe 2: Q₂ = 0.025 ft³/s Pipe 3: dy = 1.5 in. V₁ = ?! Q₁ =?
Q4: A 300 L/s of water flow through pipe Shown in figure (4). The pressure at entrance is 70 KPa. Calculate the force by fluid of sp.gr-0.9 on the bend if the volume of bend is 0.085 m³. (R= 8.55 KN) D₁=30cm D₂=20cm 6 Q4 1.5
S2-Q4: A gear pump has an efficiency of 80% runs at a rated speed of 90000 rev per hour. If the pump delivers 2.77 liters per second with internal and external diameters of 7.5 cm and 50 mm, determine the width of the pump gear.
The diameter of a pipe at the larger end is 0.6 cm and at the smaller side is 0.3 cm the larger and smaller ends are located 8 meters and 4 meters, respectively, from a datum line. If at the larger end the velocity is 1.2 meters pee second and the pressure is 5300 kN/m^2, compute the pressure at the smaller end