Q1) Water flows through the sudden pipe expansion shown below at a flow rate of 3 m3/s. the small section (1) has a diameter D1= 25 mm while the large diameter D2= 40 mm. At section (1) the gauge pressure is 0.3 bar. Find : 1. The gauge pressure at section( 2) 2. The total force exerted by the fluid on the expansion. 1 bar= 1 atm = 10 m of water3 101.3 KN/m2

Q1) Water flows through the sudden pipe expansion shown below at a flow rate of 3 m3/s. the small section (1) has a diameter D1= 25 mm while the large diameter D2= 40 mm. At section (1) the gauge pressure is 0.3 bar. Find : 1. The gauge pressure at section( 2) 2. The total force exerted by the fluid on the expansion. 1 bar= 1 atm = 10 m of water3 101.3 KN/m2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

= 4.33 9.74m/ seć n/ 4(0.2)2 HOMEWORK Q1l A (30 N/s) flow throw the reducer of the proceeding problem ,the air in the (300mm) pipe having weight density of (9.8 N/m' ) in the flowing through the reducer producing a redaction of density .assuming that the weight density of the air in the (200 mm) pipe is (7.85 N/ m'). Calèulate the mass and volume flow rate. Q2/ (2) Water enters a conical diffusing passage (see Figure below). With a flow rate of 10ft'/s, and if the entrance cross-section area is 2 ft, what's the average velocity at the entrance to the diffuser? What must the diffuser exit area be to reduce the velocity to 0.5 ft/s? 4 = 2 f Q = 10 cfs - m = AQ: oiclooleo or boon ow.matve binl to sinsb omit letot odi stum hn th .C
The figure below shows a gasoline storage tank with cross-sectional area Asub1, filled to a depth h. The space above the gasoline contains air at pressure psub0, and the gasoline flows out the bottom of the tank through a short pipe with cross-sectional area Asub2. Derive expressions for the flow speed in the pipe and the volume flow rate. Thank you!
The device shown in the fugure below is known as a venturi. In theis specific venturi the differential pressure between locations 1 and 2 is 5 psi and the diameter ratio is D2/D1 =0.35 if D2= 8inches find the air flow rate through the frictionless venturi
Q4: Answer A or B A-Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 49 Ib/ft'. What is the mass flow rate? If viscous effects are neglected. Take the specific weight for mercury equal to 846 and for water equal to 0 62.4 at 68° F. Mercury
= Water flows into a tank and out through another pipe, as shown in the figure below. The water in the tank has a surface area, Asur f 5.6 m². At the bottom of the tank there is a door inclined at an angle = 25 degrees with respect to the horizontal. The door has a length L = 1.1 m and a width w=1 m (out of the page). The flowrate into the tank is Q₁ (t) flowrate out is Qo(t) = 0.05 m³/s At time t = Asurf = 0.26 m³/s and the 0, the water has a depth ho = 2.5 m. The density of water is p = 1000 kg/m³. Ө h(t) Qout
Q4: Answer A or B A-Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 49 lb/ft3. What is the mass flow rate? If viscous effects are neglected. Take the specific weight for the mercury equal to 846 and for water equal to 62.4 at 68 0F.
reservoir A is at elevation 90 m above datum, furnishes water to a 600 mm pipe which leads to a point at elevation 30 m, the pipe being 610 m long. Here it branches into three pipes, 200 mm, 300 mm, and 150 mm diameter. The 200 mm pipe runs 300 m and discharges to reservoir B at elevation 75 m, the 300 mm runs 450 m to reservoir D at elevation 30 m. f=0.012 what is the rate of flow towards reservoir B most nearly gives?
Is the Fh equal to the force made on the bolts at flange 1-1 in this question? And can you please plug in the values and the answer so than I can compare with my solution? Please The water flows from the nozzle through a 180-degree elbow. For example, the pipe diameter D-75mm, the nozzle diameter d=25mm, and the pressure gauge at the front of the pipe reads 60kPa. Find the force of the upper, middle and lower bolts at the flange joint 1-1 position. Assuming that four bolts are installed at the up, down, front and back, the cross-center distance of the four bolts is 150mm, the weight of the elbow and the water is 100N, and the acting position is shown in the figure.
1. in a section of horizontal piper with a diameter of 3cm the pressure is 5.21 kpa and water is flowing with a speed of 1.50m/s. the pipe narrows to 2.50cm. what is the pressure in the narrower region if water behaves like an ideal fluid of sensity 1000kg/m3 2. tensile stress a. the ratio of elasic modules to strain b. the applied force per crosssectional area c. the ratio of change in length to the orig length d. the strain per unit legth e. the same as force
VII. Suppose water is leaking from a tank through a circular hole of area A, at it's bottom. When water leaks through a hole, friction and contraction of the stream near the hole reduce the volume of the water leaving the tank per second to cAp 2gh where c(0
Fluid is flowing in a sudden expanding pipe as shown in figure. The co-efficient of expansion loss is 0.5 and expansion loss is 0.08 m. Find i. the velocity Vj in the small pipe ii. exit loss co-efficient of expansion loss= 0.5 V1=? V2=2 m/sec
Water is flowing downward in a pipe in the figure shown at 0.02 cu. m. per sec. having diameters of 8 cm. and 4 cm. respectively. Determine the values of pressures (a) at pt. 2, P2 and (b) at pt. 1, P1 if the pressure at pt. 1 is twice as great as the pressure at pt. 2. H20 8 ст. Ф 1.5 m 2 datum 4 cm. Đ