Q2// In a boiler trail of one hour duration the following observations wer kg, coal burnt = 695 kg, calorific value of coal = 30200 kJ/kg, dryness fra -0.94, pressure of the boiler= 15 bar, temperature of steam leaving the s of feed water = 80C. Calculate: (a) Thermal efficiency of the boiler without super heater. (b) Thermal efficiency of the boiler with super heater. Ans(58%:73%)

Q2// In a boiler trail of one hour duration the following observations wer kg, coal burnt = 695 kg, calorific value of coal = 30200 kJ/kg, dryness fra -0.94, pressure of the boiler= 15 bar, temperature of steam leaving the s of feed water = 80C. Calculate: (a) Thermal efficiency of the boiler without super heater. (b) Thermal efficiency of the boiler with super heater. Ans(58%:73%)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Thermodynamics
In a cyclic comprising of air compressor and expansion, workdone by a prism during the compression stroke is 9.2KJ and the heat rejected to the surrounding is 50KJ. During the expansion stroke workdone by air on the prism is 8.4KJ. a) Determine the quality of heat transferred to or from the system. Tullow oil has discovered a large volume of crude deposit at Cape-3-Point along the western coast of Ghana after years of intensive exploration. In the Company’s bid to start exploration, Green Ghana an environmental protection NGO took Tullow to court to prevent the Company from embarking on the said project citing numerous environmental concerns. b) As an energy and sustainability expert, what do you think are the side effects of the project and their remedies? A cooling water pump is operating at a speed of 1800rpm. Its flow rate is 1800L/minutes at a head of 14.4m and the power of the pump is 45kw. c) Determine the power required if the pump speed is increased…
The PV diagram below shows a sequence of processes applied to an ideal gas inside an engine 1. Which process is an isothermal compression? 2. In which process does the pressure increase with constant volume? 3. In which process is workdone on the gas? 4. What is the workdone on the gas by the process DA?
Please don't use chatgpt. I am confused with the sign (direction). Please explain correctly if you are not sure just leave it to others.
please answer asap Show complete solutions and detailed drawings also please show the steam table that is used in this problem
I need the answer quickly
Provide complete solution and detailed diagram. A refrigerator is to remove heat from the cooled space at a rate of 300 KJ/min to maintain itstemperature at - 8oC. If the air surrounding the refrigerator is 25oC, determine the minimum powerrequired for this refrigerator? A. 0.263 kw B. 0.473 kw C. 0.623 kw D. 0.984 kw
104#1. an ideal gas with R=0.062 BTU/lbm-degree R and Cv=0.158 BTU/lbm-degree R undergoes athree process cycle in a cklose system. from the initial state of 20 psia and 570degree R, the gas is compressed at coinstant pressure to 1/5 of its initial volume, process 1-2; it is then heated isochrocally to state 3, process 2-3; and finally, it expands polytopically with index n=1.5 back to its initial state, process 3-1. determine the pressure, specific volumes and temperatures at cardinal points around the cycle and the cycle thermal efficiency.
10. For the Stirling engine illustrated on the pV diagram below, what is the ratio of the heats QBC/QDA? Isothermal processes B 3T; A Di T; 2V; А. З В. Зln(2) С. -1 D. 1 Е. -3
A power plant was analysed based on Carnot cycle, the evaporator supplie 553 kJ of heat per cycle at 522°C and condenser cooling fluid was maintained1- at 26°C. Determine the thermal efficiency of this Carnot engine in percentage? Provide answer to 1 decimal place and insert the unit symbol. 1 °C is 273K in this question if required.
Explain the terms - thermo - property - state - process - cycle
1. A. Using the Steam Tables, determine the amount of cooling water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47 % moisture, mass flow rate = 7200 + (10/13) kg/hr. Cooling water enters the condenser at 12 deg Cand leaves at 21 deg C. Answer: diagrams below. Cp H20 = 4.187 KJ/kg-K): Schematic diagram of heat exchanger =condenser B. Draw the schematic diagram of the condenser and process in the PV and TS V 2. Use only the MD below to solve this Item; use it by plotting data and process to determine items being asked. Steam enters a turbine at 117.4308 atmgage and 932 deg. F, and expands isentropicaly to 177.17 inches of Hg. For 2 + (10/13 kg/sec of steam, what is (a) the ideal work done (KJ/sec) if AKE = 0 and actual exhaust enthalpy is 2700 KJ/kg. a)Ans: (b)ne =. (c]Determine: ideal steam moisture at exhaust. Ans: (d) Actual steam quality at exhaust Ans: (e) Actual steam temp g) change in entropy during the actual process. at the…