Q2/ For the state of plane stress shown below, construct a Mohr's circle and determine:- (a) the principle stress acting at this point (b) the orientation of the principle stress (c) the maximum in-plane shear stress at the point and the corresponding average normal stress (d) the orientation of the maximum in-plane shear stress (e) show the results on elements 700 kPa 100 kPa 400 kPa

Q2/ For the state of plane stress shown below, construct a Mohr's circle and determine:- (a) the principle stress acting at this point (b) the orientation of the principle stress (c) the maximum in-plane shear stress at the point and the corresponding average normal stress (d) the orientation of the maximum in-plane shear stress (e) show the results on elements 700 kPa 100 kPa 400 kPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3 / An element in plane stress at the surface of a large machine is subjected to stresses shown below. Using Mohr's circle determine the following quantities (a) the principal stresses and their directions and (b) the maximum shearing stresses and the directions of the planes on which they occur. 100 MPa 50 MPa 75 MPa 75 MPa 50 MPa 100 MPa
Direct stresses of 120 N/mm2 (tension) and 90 N/mm2 (compression) are applied at a particular point in an elastic material on two mutually perpendicular planes. The principal stress in the material is limited to 200 N/mm2 (tension). Calculate the allowable value of shear stress at the point on the given planes. Determine also the value of the other principal stress and the maximum value of shear stress at the point using Mohr’s Circle.
Determine the following for the given state of stress using the equations a. Principal Stress and Principal Plane b. Shearing Stress and Shearing Strain 13ksi 7ksi 10ksi 10ksi 7ksi 13ksi
Practice 2 A fixed ended steel beam 8m long carries a uniform load 20kN/m and an axial tensile force of 200KN. The properties of steel section is as follows: A = 7800 mm? d = 324 mm Ix = 140x10 mm ly = 16x10 mmt What is the axial stress of the beam, in MPa. What is the actual bending stress in the beam due to uniform load alone acting on the beam, in MPa. -. What is the interaction value if Fb = 210 MPa and Ft = 100 MPa? answer key а.)25.64 Мра b.) 123.43 Мра c.) 0.844
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume'stress magnitudes of 5,-80 MPa, S - 220 MPa. Sy For the given state of stress at a point in a structural member, determine the center Cand the radius R of Mohr's circle. Answers: C- MPa, R- i MPa. Save for Later Part 3 Determine the principal stresses (api > Op2 ) for this state of stress. Answers: Opl = MPa, o,2 = MPa Save for Later Part 4 For this Mohr's circle, determine the magnitude of the central angle between: (a) pointxand the point representing the principal stress opl- (b) point x and the point representing the principal stress Op2. (a) Angle - i (b) Angle - i
Find the value of normal stress if force applied is 2 N and cross sectional area 2 mm2
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 400 psi in size. (a) Determine the stresses o, Oy, and the magnitude of Tyand show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-planeshear stress acting at the point and show these stresses on an appropriate sketch (eg., see Figure 12.15 or Figure 12.16). C Answer: (a) Ox- psi Oy - psi Txy - psi (b) Op1= psi Op2 = psi Tmax in-plane= psi
Part A The stress at a point is shown on the element. Suppose that o, = 105 MPа, т - 158 MPа Determine the principal stress. (Figure 1) Enter your answers numerically using three significant figures separated by commas. VG AEo t vec ? Omax, Oint, Omin = MPа Submit Request Answer Part B Determine the absolute maximum shear stress. Express your answer with three significant figures and use the appropriate units. HA O ) ? Figure 1 of 1 > Value Units Timax in-plane = Submit Request Answer Provide Feedback
STRENGTH OF MATERIALS For the state of stress at a point shown, draw its Mohr's circle and determine the following: (a) the principal stress, and (b) the maximum in-plane shear stress and the associated average normal stress. Sketch the results on each element including the orientation.
The stresses at a point in a bar are o1 = 28N/mm2 (tensile) and o2=12N/mm2 (compressive) as shown in Figure (a) Determine the normal, tangential and resultant stress in magnitude and direction on a plane inclined at 55° to the axis of the major stress. (b) Determine the maximum intensity of shear stress in the material at the point. (c) Also, solve the same problem using Mohr's circle method and compare the results. O2 Axis of Major Stress 55°
Which of the following statements is FALSE? Select one: O A. The elastic torsion formula is applicable in estimating the internal shear stress in a shaft as long as Hooke's law applies. B. The direction of the internal shear stress in a shaft follows the direction of the applied external torque. C. A hollow shaft fixed at one end, free at the other, and with a concentrated torque applied at the free end will always have a nonzero internal shear stress on the plane of its cross-sectional area. O D. For two shafts, each fixed at one end and free at the other, with the same diameter but one is hollow while the other is solid, the hollow shaft will experience a larger maximum internal shear stress.
The stress condition at one point of an aircraft is shown in the figure. 472216 40 MPa 200 MPa 80 MPa (a) Calculate the principal stresses (b) Calculate the maximum in-plane shear stress and the average normal stress by analytical method and plotting the Mohr's circle. For each case, determine the element orientation and plot the stress state. (c) Calculate the maximum absolute shear stress at the same point.