Q2: For the soil element shown in the figure. Draw Mohr circle, locate OP (origin point), then find the stresses inclined at: 1- 75° from the horizontal plane. 2- With the horizontal plane. Q2: For the soil element shown in the figure. Draw Mohr circle, locate OP (origin point),then find the stresses inclined at: 1- 75° from the horizontal plane. 2- With the horizontalplane.120 kPa-45 plane50 kPa !50 kPa4530120 kPa

Soi classification can be done by many methods and it is having many types of soil like clayey,…

Q2: For the soil element shown in the figure. Draw Mohr circle, locate OP (origin point), then find the stresses inclined at: 1-75° from the horizontal plane. 2- With the horizontal plane. 120 kPa -45 plane 50 kPa! 50 kPa - 45 30 120 kPa

Q2: For the soil element shown in the figure. Draw Mohr circle, locate OP (origin point), then find the stresses inclined at: 1-75° from the horizontal plane. 2- With the horizontal plane. 120 kPa -45 plane 50 kPa! 50 kPa - 45 30 120 kPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A net load Q was applied on a rectangular flexible foundation. A point P is located inside the foundation soil with a vertical distance Z from the foundation bottom at center. The stress increase Δ? at Z caused by Q is always larger than zero. A. True B. False
2. For Blasius solution of laminar boundary layer, prove for the displacement thickness, U 2vx | (1 - f') dn = lim (n -- f) = 1.21678 8*. n-00 8* 1.7208 %3D VRe,
3.2 Part AB of the bar has a circular cross section with 15-mm radius, and part BC has a circular cross section with 45-mm radius. Determine the normal stress on a plane perpendicular to the bar's axis (a) in part AB of the bar and (b) in part BC of the bar. 4 kN B Problem 3.2 C 6 kN
Q4: For the soil element shown, compute the stresses acting on the plane inclined by 40° with the horizontal plane then draw Mohr circle and place the stresses with respect to O.P. 20kPa 35kPa 100kPa 300 40°
Three solid bars, each with square cross sections, make up the axial assembly shown. Two loads of P = 34 kN are applied to the assembly at flange B, two loads of Q = 24 kN are applied at C, and one load of R = 60 kN is applied at end D. Bar (1) has a width of b₁ = 98 mm. Calculate the width b₂ required for bar (2) if the normal stress magnitude in bar (2) must equal the normal stress magnitude in bar (1). P b₂ R (1) A ↑ D Answer: b₂ = i B P (2) mm
Numerical analysis G=5 N=27
The rectangular bar shown in the figure is subjected to a uniformly distributed axial loading of w = 11 kN/m and a concentrated force of P = 14 kN at B. Determine the magnitude of the maximum normal stress in the bar and its location x. Assume a = 0.9 m, b = 1.1 m, c = 20 mm, and d = 35 mm.
An aluminum-alloy block (E = 70 GPa) is loaded as shown in the diagram below. The application of this load produces a tensile strain of 500 x 10-6 at A as measured by means of a strain gage. Compute the magnitude of the applied force P and locate the neutral axis. 10 cm 15 cm 30 cm 2.5 cm Gage A
A cylindrical shaft made of steel for which the tensile yield strength o, = 550 MPa is subjected to static loads consisting of a bending moment of 700 kNmm and torsion of 400 kNmm. Determine the diameter of shaft for a factor of safety equal to 1.5 if E = 200 GPa and Poisson's ratio v 0.25; Adopt maximum shear stress failure theory.
True or False: We do not need to worry about removing the effect of water from the soil weights to get the effective stress because we are just going to add it back in by finding the neutral (water) stress. True 4 False
A concentrated load (P) is applied on the center upper rectangular solid column. The weight density of the column is y, the dimension of the upper base is (L,xB1) where (L=2B1). Find how can the dimension will change with depth to keep the vertical stress be constant at any section. Hint: L always equal to 2B
b) An electric pole is held vertically by three equally spaced wires tied at the top of the pole. Each wire is inclined at 45⁰ with a tension of 1 kN, Calculate the vertical stress increase at 1 m depth and the elastic settlement below the axis if E is given as 40 MPa and μ = 0.45. Use Boussinesq’s point load theory