A concentrated load (P) is applied on the center upper rectangular solidcolumn. The weight density of the column is y, the dimension of the upperbase is (L,xB1) where (L=2B1). Find how can the dimension will changewith depth to keep the vertical stress be constant at any section.Hint: L always equal to 2B

As we move downward so due to the weight of the column stress will increase. So, to keep the…

A concentrated load (P) is applied on the center upper rectangular solid column. The weight density of the column is y, the dimension of the upper base is (L,xB1) where (L=2B¡). Find how can the dimension will change with depth to keep the vertical stress be constant at any section.

A concentrated load (P) is applied on the center upper rectangular solid column. The weight density of the column is y, the dimension of the upper base is (L,xB1) where (L=2B¡). Find how can the dimension will change with depth to keep the vertical stress be constant at any section.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

A: each member cross sectional area =-2.4 in2a=3.50 ftb=4.20 ftNormal stress in each member not exceed…

Q: The one end of a hollow square tube whose side is ( 10 + N/100 ) in with ( 1 + N/100 ) in thickness…

Q: 3. Determine the principal stresses . 02 and the principal direction a, from the following stress…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm².…

A: To find the intensity of the uniformly distributed load (w) for the given condition.

Q: В (1) (2) C Answer: Pmax =

A: Thickness=7mm Outside diameter of pipe 2=46mm Inside diameter of pipe 2=46-2*7 =32mm

Q: Problem #1. The figure below are 2 solid cylindrical bars joined together at point B. Find the…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 12 mm2.…

A: ###Determination of length a so that normal stress is same in each rod###

Q: A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is…

Q: Problem 4:a) Determine the stresses ox, oy, and Txy, and show them on a stress element. (b)…

A: In this question are mohr's circle is given Scale of mohr circle is one grid square is equal to 5…

Q: 11. In pre-stressed concrete member, the pre stressing force is: a. increased with time c. remained…

A: Solution 11) Solution In the prestressed concrete, the prestressed force is decreased with time due…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm².…

A: Given Data Cross sectional area of rod-1 (A1) = 10 mm2 Cross sectional area of rod-2 (A2) = 15 mm2…

Q: If a small concrete cube is submerged deep in still water in such a way that the pressure exerted…

A: Given data: Small cube is submerged deep in still water, where the pressure exerted on all face of…

Q: Determine the stresses ox, oy, and Txy, and show them on a stress element. (b) Determine the…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

Q: For the given stress element, draw the Mohr's circle and determine the principle stresses and…

A: σ1 = 30 kpaσ2 = -40 kpaτ = 20 kpaPrincipal stresees are given byσ1,σ2 =σ1+σ22±σ1-σ222+τ2σ1,σ2…

Q: -57. Determine the principal stress, the maximum in-plane shear stress, and ver 120 MPa MADARAKAN…

A: Given data : The value of normal stress in X direction σX=300 MPa The value of normal stress in Y…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 3100 mm² and an…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 7 mm².…

Q: Find maximum principal stress

A: Given data : The value of normal stress in X direction σX=-30 MPa The value of normal stress in Y…

Q: Determine maximum shear stress

A: Given data : Maximum principal stress σP1=32 MPaMinimum principal stress σP2=-28 MPa

Q: shear stress developed in the shaft. The shaft has an outer diameter of 90 mm, and the thickness of…

Q: A simply supported wood beam with overhang is subjected to uniformly distributed load q. 9 с 200 mm…

Q: The rectangular bar has a width of w= 2.75 in. and a thickness of t = 2.00 in. The normal stress on…

A: Given : W = 2/75 in. t = 2.00 in Normal stress on plane AB of the rectangular block is 6ksi

Q: Q-1 The factor of safety for a machine element depends on the particular point selected for…

Q: In order to reinforced a column in an existing structure, two channels are welded to the column as…

A: Given: Section: W 12 x 50 C 6 x 13 Effective length of the column, KL=4.9 m Fy = 350 MPa Fu = 450…

Q: 3. The steel pipe is supported on the circular base plate and concrete pedestal. If the normal…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: The internal shear force Vat a certain section of an aluminum beam is 6.8 kN. If the beam has the…

Q: A hollow crank with an outside diameter of 4.8 in. and a wall thickness of 0.21 in. is subjected to…

A: The outer diameter = 4.8 inThe thickness of the crack = 0.21 inThe forces acting in the members are…

Q: For the structure below, assume that a = 60 in., b = 90 in., c = 40 in., and d = 50 in. Determine…

A: The given structure is analyzed by using the equation of equilibrium forces. The sum of all forces…

Q: The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure…

Q: Ata point in a stressed body, the known stresses are o, = and T = 0, Determine a) the normal and…

Q: 2. In the structure below, the vertical bar A has a modulus of elasticity of 210 GPa, a length of…

Q: Question 1 of 5 /20 E View Policies Current Attempt in Progress The solid 1.05-in-diameter rod is…

Q: A solid 2.40 in. diameter shaft is subjected to a torque of T = 330 lb-ft and an axial load of P =…

Q: 0, = 100MP. %3D = 300MPA 0,= 400,MPa

A: Determine maximum principal stress

Q: The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Determine the shear strain y at corner Q' after deformation.

Q: The internal shear force V at a certain section of an aluminum beam is 10.5 kN. If the beam has the…

Q: X Incorrect "he extruded plastic shape will be subjected to an internal shear force of V = 380 lb.…

A: To solve this question we will first find the neutral axis distance. Then we will calculate the…

Q: member with 0.2-in. wall thickness (3), cach supports an axial tensile load of 5 ki (a) Determine…

A: for easier calculations first all units are converted in to SI and for simplicity again convered…

Q: The internal shear force V at a certain section of an aluminum beam is 10.2 kN. If the beam has the…

A: Given Data Width of flange = 69mm thickness of flange = 4mm Depth of beam = 72 mm Height of web =…

Q: The line of action of the 75-kip axial load Pis parallel to the geometric axis of the column AB and…

A: P = 75 kipx = 0.6 in E = 29 x 106 psi

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

A concentrated load (P) is applied on the center upper rectangular solid
column. The weight density of the column is y, the dimension of the upper
base is (L,xB1) where (L=2B1). Find how can the dimension will change
with depth to keep the vertical stress be constant at any section.
Hint: L always equal to 2B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2) Complete solution and correct units pls. Thanks
Find max and min stresses. Please provide step by step solution. Don't copy!!
Kindly please answer with the most complete utmost solution. Thanskl!
The column is constructed from high-strength concrete and A-36 steel reinforcing rods. If it is subjected to an axial force of 30 kips, determine the average normal stress in each rod (ksi). Each rod has a diameter of 0.58 inch. Esteel = 29 x 103 psi and Econcrete = 4.2 x 103 psi, r = 4 inches
2
The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is 0.04 in. Determine the maximum allowable value of P in kips. -0.75 in A B C 50 kips 3 in 20 in 30 in
Problem 1: Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T=2880 N and T;=432 N. The maximum bending moment is atx= 230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). y 230 mm T, 280 mm 30-mm dia. T C 300 mm 250-mm dia. 400-mm dia. 270 N 1800 N a) Sketch a general shaft layout in 2D (x – y axes), including all components and torques, then calculate all reactions. b) Based on the current shaft dimensions and using only forces at B and C, find the lowest critical speed of the shaft. c) Discard the indicated shaft diameter and use DE-Goodman criteria to determine the critical diameter of the shaft based on infinite fatigue life with a design factor n of 1.5. (Take the same value of endurance limit as that used in…
A steel bar 50 mm diameter and 1 m long just fits within a rigid hole carries a compressive load of 300 kN. Consider E= 200 GPa for steel and Poissons ratio υ = 1/4. Determine: (a.)Stress developed along lateral direction in MPa. (b.) Stress developed along lateral direction in MPa if the rigid hole has a diameter of 51 mm.
X= 482 show complete solutions and FBD
A rectangular reinforced concrete beam has a width of 300 mm and an effective depth of 700 mm. It is subjected to a nominal moment of 550 kN-m. If fc = 28 MPa, fy = 280 MPa, and Es = 200 GPa. a. Determine the balance steel ratio in percent; b. Solve for the depth of the equivalent rectangular stress block; c. Check whether the beam is tension-controlled, compression-controlled, or within the transition region and determine the value of the strength reduction factor, ; d.Solve for the ultimate moment capacity of the beam.