Q2: Draw the S.F. and B.M. diagrams for the beam which is loaded as shown in Fig. Determine the points of contraflexure within the span AB. 16 KN 4 kN 2KN 10 m 6m 16m

Q: How does Impulsive forces occur?

A: Impulsive force:- When a force acted on a body for short period of time then it is called impulsive…

Q:

A: from the given options, it seems option 1 is correct

Q: what are the symbols for frictional force, applied force, normal force, and gravitational force?

A: ■ The frictional force exist due to surface roughness and the relative motion between the bodies. ■…

Q: What is known as extensive quantities ?

A: Extensive properties are those properties that depend upon the mass of the system. The energy…

Q: Explain the temperature Changes: Heat Capacity ?

A: Temperature change- process where the temperature of body changes or hotness of body changes  i.e in…

Q: Prove please!

A:

Q: All physical quantities involve a direction

A: Given Physical quantity To find Direction based physical quantity

Q: Thank you

A: given : t = 6.07mm = 0.00607 m F = 38.9 KN = 38900 N τ = 54.4 MPa = 54.4 x 106 N/m2

Q: In rolling contact bearings, balls and rollers are used to reduce between rotating surfaces.

A: In case of rolling contact bearings, the type of contact is a point or a line. Bearings are…

Q: required for theoretieally correet combustion. (i) Estimate the volumetric composition of dry…

A:

Q: If a car weighing 2400 lbs is able to go 1000 ft up a mountain incline whose angle of inclination is…

A: Given data: Weight of car = 2400 lbs                      Distance which car moves up the incline =…

Q: 180 200 30 Find F and Lacation 令 ocation 200

A:

Q: Define the Temperature Scales?

A:

Q: (3) In Sample Problem 15.04, the constant"kappa" is *

A:

Q: Which of the following does not belong to the group? force stress time velocity

A:

Q: ptotic  relationship?

A: Power:- Power is the amount of work done in a given amount of time or the rate at which work is…

Q: It causes resistance due to applied forces which is a result of restrain deformations   Shear Force…

A:

Q: An open top tank within the lab contains a hot fluid which is gradually cooled whilst the fluid is…

A:

Q: Thank you, I understand it now! What value of g did you use?

A:

Q: Hi could you also please give the solution to d, e, f

A: As per the guidelines we are subjected to solve only 3 sub parts at a time. Please repost the same…

Q: Define 'power'.

A: It can simply defined as the amount of work done per unit time. Or the rate of time of doing work or…

Q: How did you combine eq1 and eq2?

A:

Q: mber of barrels of oil required per day if the efficiency of  the fuel oil plant is 25%.  ii.…

A: The powerplant is a set of mechanical devices which is used to produce the power output to run the…

Q: 1.Convert 21 inches of Hg (vacuum, gauge) to kPa (absolute)

A: Since you have posted a multiple independent question in a single question we will solve first…

Q: When do stress concentrations occur?

A: Stress concentration, It is a location within an object where the magnitude of stress is high as…

Q: 1. A saw blade with a 12-inch diameter, uniformly accelerates from rest to 800 rpm in 20 seconds.…

A:

Q: How do we get 2.264 and .4415?

A: Given Data

Q: "If we push the book on the table, it stops after sometime. Why?"

A: If we push the book on the table, then the book will get some speed. but after some time the book…

Q: Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and…

A: Given: The center distance between shafts is 1.67 ft. The speed of the input shaft is 350 rpm. The…

Q: Give the steps by steps explanation of the previous answer

A:

Q: Q2/ Fill in the blanks with suitable phrases or terms:- 1- The typical composition of austenitic…

A: 1. The typical composition of austenitic stainless steel is            Note :- you have posted…

Q: (a) Plot a torque diagram showing the internal torque in segments (1), (2) and (3) of the shaft.…

A: