Q2: Design the Wein-bridge oscillator in figure below to oscillate fr = 35 kHz. at Choose appropriate component values. R₁ +2R1 Ri fr= EXRC RIXR₂ RITRE 3R₁ 2R₁ R₁ www =C R₂ www + Hww www. CR 2₁ Zp 1

Q: Q2) design a wien bridge to produce an output sinusoid that can be adjusted from 400 Hz to 100 kHz…

A:

Q: Briefly explain how the oscillation begin? RB VCC DISCHARGE. THRESHOLD TRIGGER www RESET VCC R SQ…

A: Given:Astable multivibratoror.Required:We need to explain how oscillations begin in an astable…

Q: Obtain the transfer function of the electrical system of Figure. Draw a schematic diagram of an…

A: The given circuit diagram is shown below,

Q: Usually, a multistage amplifier connection can

A: Amplifier An electronic device or we can say circuit arrangement in which for small amplitude signal…

Q: XPG1 xsc2 Probel v 154V vi 62.0u Pre: 400 e R4 Probe2 18 kQ vp 30.0 v Probed Prea 400 kP C2 C1 V1…

A:

Q: Show the capacitors, whether it is effective at low or high frequencsies Draw low frequency…

A: To analyse the condition

Q: Given hfe = 60, hie=10000, hoe = 20μ 0, hre = 2*10^-4. Find the current gain of the BJT, correct up…

A:

Q: 2! Cal Culate and draw the out put signal for verting opamp årcuit if Vin=3Sint-2 Rf =4K Please draw…

A:

Q: R=0.5 kQ Oa o ww

A: Given, Vp=0.7 VVz1=2.3 VVz2=5.6 V For the diode to be operated in forward bias condition,…

Q: Design a Wien Bridge oscillator circuit with an amplifying gain of 13 and an oscillating frequency…

A:

Q: Q3) three point charges Q₁=1 nC, Q=-3 nC and Q₁-2 nC in free space, are positioned one at a time and…

A: total energy consumed is calculated as

Q: Determine the peak value of the output voltage for Figure. if the turns ratio is 3:1.

A: Given: Vpin=170 V Turns Ratio = 3:1 The voltage ratio can be given as below in the transformer;…

Q: 2/ Fud the Ua lue Cs For t:15 Hz for the followng figure hfe:200, hie:2,5k

A:

Q: Design a square wave generator to produce a square wave of 5Khz frequency. The practical OP-AMP 741…

A:

Q: Consider the following circuit. The frequency of oscillation is:

A: The given circuit is a Colpitts oscillator and the frequency of oscillation is based on the feedback…

Q: Write output waveform 20kQ 10kQ INPUT OUTPUT Write output waveform 20ΚΩ aww 10kQ INPUT A OUTPUT

A:

Q: Problem F Design component values to produce a 2.4 kHz square wave. Assume the op amp output can go…

A: Need to design the Astable multivibrator circuit to generate the square wave of 2.4KHz. The…

Q: 1. If a sinusoidal signal voltage of 8V(PP) is applied to each amplifier in the figure below, what…

A: Vin=8 Vpeak to peak sinusoidal voltage The above circuit is a voltage follower, where the output…

Q: Q2.Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Ro 1.0 KM www Bpc = 50 10 V 20…

A: We need to find out the current and voltage for given circuit.

Q: the input is a.-sin (wt) b.none of the above c.sin

A:

Q: Perform an AC analysis for the following circuit. Show the waveform measured at the OUTPUT from 10…

A: To perform an AC analysis for the given inverting op-amp amplifier circuit, we'll use the specified…

Q: Q.2/ Find the value of R2 in figure below so that the circuit will oscillate.

A: We will answer the first question since the exact one was not specified. Please submit a new…

Q: 4. A 300 2 resistor R and a 200 µF capacitor are connected in series across an ac power supply which…

A: We need to analyse the given circuit in frequency domain .

Q: Design an alternate circuit for square and triangular wave generation using a single capacitor in…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Pne maximum deviation allowed w an Fm broadsas systerm is 75KHZ. If the modulating signal ba eignal…

A:

Q: For the circuit shown, if VO = 7.5V the value of Rx is equal to . LM317 Vo Vi = 15V 1250 Iadj =10µA…

A: Fig: Given circuit  For given circuit  voltage at node B is  VB=RxRx+125V0Given…

Q: Explain the physical processes, that occur in RC and RL circuits when there are bursts of voltage…

A: The answer as given below:

Q: EXPERIMENT 01 10V- 8V- 6V- 4V- 2V- OV- -2V- 4V- 6V- 8V- 10V- 0.00ms EXPERIMENT 01 V(n002)…

A: Given: In this question, the given details are, We want to measure the output peak value, is it…

Q: 2Vm Vm Vm DC level Vi D, RL Vo t -Vm Input waveform Output waveform Positive clamper

A:

Q: Consider a Schmitt trigger circuit with + VSAT = + 12 V, V,T = 4V, and V,T =0 V. This circuit is…

A:

Q: Q5/ Design a Colpitts oscillator as shown in figure below with 10 MHz output frequency. Find the…

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: Design a Comparator Circuit that have V¢ = +8V -Vcc=-8V, V reference = 4 V at non-inverting terminal…

A: To answer above question, one should know what an amplifier is. An amplifier is an electronic…

Q: 1 msec an %3D :Design an op-amp free running multivibrator with TON TOFF= 2 msec. %3D

A:

Q: Consider the circuit in Figure A2 where Vs = 12 V, R₁ R₂ and the input is a sinusoidal signal with…

A:

Filter

A filter is a device or process which removes some of the unwanted features or components like frequencies from a signal in signal processing. The feature of filters is the complete or partial suppression of some part of the signal, and filtering is a class of signal processing. This most often means removing some frequency bands or some frequencies. In the frequency domain, the filters do not exclusively act, especially in the image processing field many other targets for filtering exist. Without having to act in the frequency domain, the correlations can be removed for certain frequency components and not for others. The filters are widely used in electronics and telecommunication, in television, radio, radar, audio recording, music synthesis, control systems, computer graphics, and image processing.