Q2) Consider the full wave rectifier circuit shown in fig 2 .The converter is operating with firing angle delay angle 45° 1. Draw and calculate the average output voltage 2. The load current in Amper 3. Determine the output power 4. Accurately plot the current through the two thyristor V1= 220 sinwt T1 100 mH V2= 220 sin (wt-180) T2 2 ohm

Q2) Consider the full wave rectifier circuit shown in fig 2 .The converter is operating with firing angle delay angle 45° 1. Draw and calculate the average output voltage 2. The load current in Amper 3. Determine the output power 4. Accurately plot the current through the two thyristor V1= 220 sinwt T1 100 mH V2= 220 sin (wt-180) T2 2 ohm

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
In a single phase half-wave controlled rectifier has 400 sinwt as the input voltage and R as the load.For the firing angle of 60 degrees for the SCR,the average output voltage is a. 300/pi b. 200/pi c. 240/pi d. 400/pi
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V omsh RL VI-DC20V 0.01 F 0.02 F 0.0167 F None of the above
Q2) The expected average and RMS output voltage of the following PLECS circuit is equal to Single-phase diode rectifier L: 0.05 01 V_R (V i_N Scope V: 120 w: 2*pi*60 v_N R: 2.50 C: 500e-6 Oa) 40V, 84.85 V Ob) 38 V, 84.85V c) 38V, 80.2V O d) 40V, 38V Probe Probe
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 74 V and the firing angle of the SCR is 60 degrees, the RMS voltage at the input would be: O A. 220 V O B.99 V O C. None of the other choices are correct OD. 110 V O E.256 V
A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Value: Student No. Last 1 digit ( will be selected as kΩ, LastThose whose number is "0" get "9")a) How many % of conduction does each diode branch stay on?b) Find the average values of the load voltage.c) Find the average values of the load current.d) Find the effective value of the load voltage.e) Find the effective value of the load current.
A half-wave rectifier circuit has an input voltage of 60V for the entire swing of the input signal from the secondary winding of the transformer. If the load resistance is 902 and a shunt capacitor is connected therein: 1. Draw the circuit 2. Solve the following unknown values. a. The peak voltage Vm b. the average output voltage Vo(ave)
Assume AT the output of a filtered half wave rectifier circuit a series resistor RS of 4.2kohm together with a shunt connected 54v zener diode is now connected as a simple regulated circuit. The zener is connected in parallel with load RL of 11.9 kohm. When the input mains voltage flutes at various parts of day the max DC voltage appearing across the capacitor is 120 V and thefor the above zener maximum voltage is 80 V. Determine the load current in mA flowing through the load,
The power output of the half-wave rectifier is rated at 25.6 W with a load resistor of 10 ohms. The average voltage at the output is: O A. 32 V O B. None of the other choices are correct O C. 8 V O D. 16 V O E. 64 V
A 1 - ∅ full-wave rectifier is made by using thyristors. If the peak value of the sinusoidal input voltage is Vm and the value of the delay angle is 45 degree, find the average value of output voltage Select one: a. 0.65 VM b. 0.85 VM c. 0.45 VM d. 0.25 Vm