Q2) A block of weight W slides down an inclined plane on a thin film of oil with terminal velocity V, as shown in Figure Q2, and thus a shear stress will be existed (1). The film contact area is A and its thickness h, oil viscosity u and incline angle 0. Assuming a linear velocity distribution in the film, prove that the analytic expression for the terminal velocity can be V=(hWcos®) /Aµ. For both Group 1 and Group 2 W Oil film, thickness h Figure Q2

Q2) A block of weight W slides down an inclined plane on a thin film of oil with terminal velocity V, as shown in Figure Q2, and thus a shear stress will be existed (1). The film contact area is A and its thickness h, oil viscosity u and incline angle 0. Assuming a linear velocity distribution in the film, prove that the analytic expression for the terminal velocity can be V=(hWcos®) /Aµ. For both Group 1 and Group 2 W Oil film, thickness h Figure Q2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An incompressible fluid (kinematic viscosity, 7.4 x10-7 m²/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is rt of this book may be repro
plz help me with this one , i would appreciate it if you can help me now. A piston with a diameter of 0.8 m and width of L=0.6 m rotates with 6 rad/s inside a cylinder that has a diameter of 1 m that filled with oil that has a viscosity of 8x10-3 N.s/m2 What is the shear force that acts on the circumference of the piston (N)? Assume the variation in velocity of the oil is linear.
A square block has 320 mm bottom sides dimensions, weighing W is 1.4 kN on an edge slides down an incline angle 0 is 20° on a film of oil 6 mm thickness, as shown below. Assuming a linear velocity profile in the oil. The viscosity of the oil is 0.009 Pa.s. W y Determine the force acting on the block, F. What is the velocity of the block, V?
Ex. The force required to tow a 1:30scale model of a motor boat in a lake at a speed of 2m/s is 0.5 N, Assuming that the viscosity resistance due to water and air is negligible in comparison with the wave resistance, calculate the corresponding speed of the prototype for dynamically similar conditions. What would be the force required to propel the prptype at that velocity in the same lake? Ans.: 10.95m/s, 13500N
1) The velocity profile of a viscus fluid over a plate is parabolie with vertex 25 em from the plate ,where the velocity 125 cm/s. calculate the velocity gradient and shear stress at distance of (0, 5, 15 and 25 cm) from the plate given the viscosity of the fluid =7 poise ? Also draw the figure explain the relationship between the velocity gradient and shear stress. Take velocity profile for parabolic equation, (v = ay + by + c)
At a certain point in castor oil the shear stress is 0.216 N/m and the velocity gradient 0.216 s. If mass density of castor oil is 959.42 ka/m. Find kinematic viscosity.
QA An incompressible fluid (kinematic viscosity, 7.4 x10-7 m2/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is (a) 0.651 x 10-3 (c) 6.51 (b) 0.651 (d) 0.651 x 103
A jet engine on a test stand directs a stream of hot exhaust gasses against a vemcal wall. All of the exhaust gas leaving the wall after impact is in the y-z plane (ie no "x" direction velocity). The mass rate is 200 kg/s and the velocity is 400 m/s. (Note that the density and viscosity are not relevant) What is the force on the wall (include direction)?
HW1.1: Equation 2.7 in the text provides the velocity profile, u(y) for a narrow, infinitely long, slit-like microchannel. Use the no-slip boundary conditions (channel walls not moving) to obtain 1 dp - hy} 2n dx the standard solution, u(y)= For an incompressible, Newtonian fluid, with fluid properties as described in the text, shear stress du is typically given by t =n· dy Write-out an expression for the shear stress as a function of y. Calculate shear stress at: (a) y = 0; (b) y = h; and (c) y = h/2.
Q1/ A 120 mm disc rotates on a table separated by an oil film of 1.8 mm thickness. Find the viscosity of oil if the torque required to rotate the dise at 60 r.p.m is 3.6 x 10 N.m. Assume the velocity gradient in the oil film to be linear u= 0.0506 poise. %3D N-60 r.p.m. Dise 1.8 mm Oil film (1= dy) 120 mm Table Figure (1)
is called a cone-plate viscometer A solid cone of angle 2k, base 1, and density p, is rotat- Ing with initial angular velocity my inside a conical.seat, as shown in Fig. of viscosity u. Neglecting air drag, derive an analytical ex- pression for the cone's angular velocity ) if there is no applied tongue. The device in Fig. The angle of the cone is very small, so thiat sin 0 0, and the gap is filled with the test liquid. The torque M to rotate the cone at a rate 1 is measured. Assuming a lin- ear velocity profile in the fluid film, derive an expression for tiuid viscosity u as a tumction of (M, R. S2, 0). The clearance h is filled with nil Bave C co radius a dwit) dt Fluid I manmot 1Inentia Derive an expression for the capillary height change h for a fluid of surface tension Y and contact angle 0 between two vertical parallel plates a distance W apart, as in Fig. . What will li be for water at 20°C if W = 0.5 mm? A thin plate is separated from two fixed plates by very vis- cous liquids…
There is oil (dynamic viscosity = 1.6 Pa.s), oil film thickness (h = 0.7 mm) between a block with mass M (5 kg) and the bottom surface. Block base surface Its area is given as A = 28 cm2. Block m (1kg weight) with a wire rope It depends on the mass. At time t = 0, mass m is released. According to these data; a)Find the viscous forces when the block moves with V = 1 m / s velocity. b)Derive an equation for the block velocity as a function of time (t). c)Plot the velocity-time variation for t = 0 and t = t.