Q1. Given the following system, find the shear stress in kg/m², developed on the fixed plate. The kinematic viscosity of the fluid is 4.4x104 m²/s and the specific weight of the fluid is 1.62 t/m³. y U 3 и 1.5 - 0.5 () U fluid u U= 12 cm/s, h= 22 cm fixed plate

Q1. Given the following system, find the shear stress in kg/m², developed on the fixed plate. The kinematic viscosity of the fluid is 4.4x104 m²/s and the specific weight of the fluid is 1.62 t/m³. y U 3 и 1.5 - 0.5 () U fluid u U= 12 cm/s, h= 22 cm fixed plate

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.3 A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, determine the pressure in A. 1.4 The absolute viscosity of a fluid at atmospheric conditions is 8 x 10-3 kgf-s/m2. Find this viscosity in: a) Reyn; b) Poise; c) lbf-s/ft2; d) Pa-s.
Can i get the answer as an image i cant see the hold write up Tried using my laptop same issue
n = Xe()r -------Equation 1 where X = 1.7419 and (E/R) = -0.018 are constants for a given fluid. You are required to carry out appropriate calculations on the effect of changes in temperature given in table A by using equation 1 for Ethanol on the viscosity of a fluid. Table A NO Temperature viscocity n T°C cP 10 3 20 30 5 40 6. 50 7 60 8 70 In addition to this, calculate other constraints such as the variety of shear stress (T) and force due to fluid viscosity, when the two layers of different compressible Newtonian fluids are contained between two flat plates separated by a distance of 0.05m and fluid moving with the velocity of 2m/s in the horizontal direction. Assume the shear area between the fluid layers is 0.5m². To do this you required to explain, with examples, the effects of temperature and shear forces on Newtonian and non-Newtonian fluid. Also, explain the operation and constraints of different viscometers that quantify viscosity in fluids. 2.
The Cauchy stress tensor for a (compressible) Newtonian fluid is given by S(x, t) = -p(x, t)I+ A (V · v(x, t)) I+ 2µ sym Vv(x, t). Choose from the list below the expression corresponding to the divergence of the Cauchy stress. V. S(x, t) = - Vp(x,t) + µ Av(x, t) | V. S(x, t) = - Vp(x, t) + AV (V · v(x, t))+ µAv(x, t) None of the above V (x, t) = - Vp(x, t) + (A + µ)▼ (V · v(x, t)) + µ Av(x, t)
YouTube mana TWILCH Cônan Filler and rear edges (in kN/m). (take Y=9.8 kN/m" for water) Your answer 10 points Shaft (250 mm diameter) rotates at 250 rpm inside a sleeve (251 mm diameter) with a constant clearance. the power required to rotate the shaft is 2204 watts, find the viscosity (N.sec/m²) of lubricant oil in the clearance. Take length of sleeve as 150 mm. Your answer 10 points SHOT ON BLACK SHARK 2 AI DUAL CAMERA Oil
A viscous incompressible liquid of density p and of dynamic viscosity n is carried upwards against gravity with the aid of moving side walls. This laminar flow is steady and fully developed in z-direction and there is no applied pressure gradient. The coordinate is fixed in the midway between the walls as shown below. 2d g=-gk liquid P, n x=-d x=d I. The velocity profile in z-direction is pg w(x) = (x2 – d) + U. 2n II. To be able to carry a net amount of liquid upwards, the wall velocities need to be greater than pgd²/(2n). III. If one of the walls stops, increasing the speed of the other wall to 3/2U would carry the same amount of liquid upwards. Which of the above statements are true?
Calculate the fluid force on the side of the "infinite" plate B in the figure. The fluid mass 850kg/m³. /m³. Assume g = 9.8m/s². density is p F N = A y = ln x x
A fluid is being pumped through a pipe. The density of fluid is 872 kg/m³. The viscosity is 2.8x102 Pa.s. The velocity in the pipe is 5.9 m/s. If the Reynolds number is 2100. a- What is the pipe cross-sectional area? b- If the pipe cross-sectional area increased 1.5 fold under same Reynold number, density and viscosity, what is the new velocity?
Two plates are separated by 30 mm space. The lower plate moves at velocity of 2 m/s while the upper plate moves at a velocity of 8 m/s. Oil (S=0.48) which fills the space. The oil viscosity is equal to 0.003 m Is. The variation in velocity of the oil is linear. What is the shear stress in the oil (N/m2)? upper plate -8 m/s OIL 30 mm 2 m/s lower plate ENG LIS
Choose the correct answer
1.).A cylindrical shaft of radius 5 cm is rotating at a speed of 50 rad/s in a cylindrical bearing . Shaft and bearing are concentric . The lubricant of viscosity 0,6 Pa s and SG= 0,9 completely fills the clearance between shaft and bearing surface. Take clearance as 0,5 cm and length of shaft as 10 cm . The lubricant flow is laminar steady and uniform . Frictional force on shaft surface is ? ANSWER:9,42 N
b