Q1//Using the ACI Code equations, determine the minimum slab thickness required for Panel (A) and Panel (B) of the floor system shown in Figure (1). Use fy=350MPA. - 200mm 350mm 300mm Exterior beam 300x300mm 200mm Panel (A) Panel (B) 350mm 300mm Interior beam 6.5 m 6.4 m - 6.5 m Figure (1) 5.1 m 5.1m

Q1//Using the ACI Code equations, determine the minimum slab thickness required for Panel (A) and Panel (B) of the floor system shown in Figure (1). Use fy=350MPA. - 200mm 350mm 300mm Exterior beam 300x300mm 200mm Panel (A) Panel (B) 350mm 300mm Interior beam 6.5 m 6.4 m - 6.5 m Figure (1) 5.1 m 5.1m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

III. Locate the centroid of the composite area below. Y 50 80 mm, mm R=50mm 250mm R=65mm -- X 50 50 mm mm
2. A uniform concrete slab is to be attached to two rods whose lowers ends are initially at the same level. What is the required area, in mm?, of aluminum rod so that slab will remain level after it is attached to the rods? Wi4 m Aluminum E = 72 GPa Steel A= 8V mm 2 E = 200 GPa WI4 m -Y/40 m- Y/200 m
Situation III: Given the grouped data for the strengths of the reinforcing steel bars. 7. Determine the mean. 8. Determine the median. 9. Determine the mode. Bar Strength Number of (MPa) bars. 240-269 7 270-299 11 300-329 4 330-359 17 360-389 22
Q3 Eor the solid slabs shown in Fig (3). find the spacing of (4 12 mm ) bars required at the locations and directions that idicated by the arrows? Assume - f =30 MPa . Fy =400 MPa Slab thickness = 150 mm Col 35+35 e o Al columas are square of 350 ma = 350 mm T
The two-way slab shown in the following Figure has been assumed to have a thickness of 7 in. Section A-A in the figure shows the beam cross section. Check the ACI equations to determine if the slab thickness is satisfactory for an interior panel. f = 3000 psi, fy = 60,000 psi, and normal- weight concrete. 23t 23ft 23t 19 ft all clum く !! IS i A 19t a. 7.20 (in) b. 6.65 (in) C. 6.18 (in) d. 7.84 (in)
Define the following a(Point of contra flexureb) Section modulus
Problem 1 Considering flexural buckling, determine the allowable and design compressive strength using L = 5m (A = 6,265mm2, rx = 106.43mm, ry = 49.28mm %3D %3D W10× 33 L A992 steel
The three parts of this problem refer to the floor plan shown in the figure. Assume that the entire floor system isconstructed sand normal weight concrete that has compressive strength, fc= 4000psi. Also assume that thelongitudinal steel has a yield strength, fy=40 ksi, and that the transverse steel has a yield strength off yt= 40ksi. The slab thickness is 6”, with a superimposed dead load of 18 psf and live load of 26 psf.a).Design the spandrel beam between columns B1 and C1 for bending, shear, and torsion. Check that all of theappropriate ACI Code requirements for strength, minimum-reinforcement area, and reinforcement spacing are satisfied.b): Design the spandrel beam between columns A1 and A2 for bending, shear, and torsion. Check that all of theappropriate ACI Code requirements for strength, minimum-reinforcement area, and reinforcement spacing are satisfied.c). Design the spandrel beam between columns B2 and C2 for bending, shear, development length, andsplicing. Check that all…
Q2/Using the ACI Code equations, determine the minimum slab thickness required for Panel (A and Panel (B) of the floor system shown in Figure (2). Use fy-470MPA. 200mm 350mm e 250mm 400mm dia. Exterior beam 250x250mm 200mm 2500 x 1000mm 350mm Panel (A) Panel (B) 50mm Interior beam 78 m 7.8m 78 m 78m Figure (2) 7.5 m-
According to ACI code min allowed diameter of circular column is 450mm 450cm 300cm 300mm * In design of slab shear if Vu more than ØVc then increase slab thickness use strirrups decrease slab thickness use additional longitudinal reinforcement
12" fc= 3.5 ksi 30" 26" fy= = 40 ksi n= 9 As =8#6 Find fr (modulous of rupture) = ? M, bending moment = ? k =? j=? g=? I=? %3D
Problem. A 130 thick one way RC slab is subjected to loads (wt. of slab is not included) as shown. Solve & Draw V & M diagram. Use: fy= 415 MPa; fc'=25 MPa; cc=27 mm. LL-2.3 KPa/DL = 5.5KPa 5.70m 25mm REBARS @ 230 mm O.C. 2m 24mm REBARS @ 130 mm O.C.