Q1A If the signal 4 cos (2r10³t) is used to modulate 13 cos (27 10°t) carrier, (a) find the transmission efficiency, (b) compute the total and the USB powers, (c) draw the magnitude spectrum of the transmitted AM signal showing the exact numerical values of the powers and the frequencies.

Q1A If the signal 4 cos (2r10³t) is used to modulate 13 cos (27 10°t) carrier, (a) find the transmission efficiency, (b) compute the total and the USB powers, (c) draw the magnitude spectrum of the transmitted AM signal showing the exact numerical values of the powers and the frequencies.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

AM transmitter develops a power output of (110 W) across a (70 22) resistive load when a sinusoidal test tone with a peak amplitude of (4 V) is applied to the input of the modulator it is found that the power output increases by 50% of unmodulated power output under these conditions determine: 1- The average power output in each sideband. 2- Modulation index. 3- The peak amplitude of the modulated waveform. 4- The total average power in the output if the amplitude of the modulating sinusoid is reduced to 3 V. Ps=59W, m=0.6, Amax=244.2, PT=144.9W O Ps=55W, m=1, Amax=248.2, PT=140.9W O Ps=58W, m=0.7, Amax=245.2, PT-143.9W O Ps=56W, m=0.9, Amax=247.2, PT=141.9W O Ps=57W, m=0.8, Amax=246.2, PT=142.9W O ...
ver is in the side dulation factor m. This emphasis .8. A carrier wave of 500 watts is subjected to 100% amplitude modulation. Determine: (ii) power of modulated wave. (i) power in sidebands Solutien
A carrier (fc = 100 MHZ, A, = 25V) is frequency modulated by the sine wave (fm = 8 kHz, Am = 3V) using a frequency modulator with frequency deviation of 58kHz. Determine: (a) Carrier swing frequency of the output FM signal. (b) Highest and lowest sidebands' frequencies generated by the modulated signal. (c) The bandwidth of the FM signal. (d) The transmitted power through a 502 load. Ignore UnB < 0.1
I need the answer as soon as possible
QB
The SNRi of an FM transmitter is determined to be 24.093dBV. Solve for the peak frequency deviation caused by the noise if the transmitter sensitivity is determined to be 368.903Hz/V, and a modulating signal of 13.926V and the modulating index is kept at 4
4. A modulated signal (AM) varies between the maximum values of +18V and -18V, if the carrier has an amplitude of 12V, a) What is the modulation index? b) What is the maximum magnitude of the modulator? c) Sketch the envelope of the modulated wave
In an AM modulator the message signal is m(t) = coswmit+2coswm2t, and the carrier wave is c(t) = Acosw.t. The modulation index is m = 0.5. a) Determine the amplitude of the carrier wave A. b) Determine the expression of the modulated signal with the AM modulation scheme. c) Determine the expression of the frequency spectrum of the AM modulated signal and then plot the frequency spectrum.
For an FM modulator with 48 kHz of frequency deviation. and a modulation signal frequency fm= 8kHz, determine the bandwidth using both the Bessel table and Carson's rule.
2. What is the frequency swing of an FM broadcast transmitter when modulated 60%?
Q7. Figure Q7 shows a modulated waveform v(t) in millivolts as a function of time t in nanoseconds. 1.5 1.0 0.5 - 0.0 -0.5 -1.0 -1.5 100 200 300 400 500 t/ns Figure Q7: Modulated waveform (a) Describe the modulation scheme. (b) What are the values of the carrier frequency and the modulation frequency? (c) What is the value of the modulation index? (d) What is the transmission efficiency (ratio of modulated to total power) in this example? (e) Sketch the spectrum of this modulated waveform indicating the relative magnitudes of the various spectral components. (f) Demodulation of this type of waveform is usually performed with an envelope detector. Describe the function of an envelope detector and sketch an example circuit. (g) What requirements on the values of the components of your envelope detector circuit are there for the successful demodulation of the given waveform? (h) Keeping the same carrier wave, the modulating wave in this example is substituted with a square wave of 50%…
Solution please .