Q12: A certain sinusoid at a frequency of fm Hz is used at the modulating signal in both an AM (DSB – LC) and an FM system. The unmodulated carrier powers are equal in both systems. When modulated, the peak frequency deviation of FM system is set to four times the bandwidth of the AM system. The magnitude of those sidebands spaced + fm Hz from carrier in both systems are equal, determine: (a)The modulation index of FM system. (b) The modulation index of AM system. 133

Q12: A certain sinusoid at a frequency of fm Hz is used at the modulating signal in both an AM (DSB – LC) and an FM system. The unmodulated carrier powers are equal in both systems. When modulated, the peak frequency deviation of FM system is set to four times the bandwidth of the AM system. The magnitude of those sidebands spaced + fm Hz from carrier in both systems are equal, determine: (a)The modulation index of FM system. (b) The modulation index of AM system. 133

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

12- A DVM measure... a- peak value. b- RMS value. Average value. d- peak to peak value. 13 The study of energy distribution across the frequency spectrum of a given electrical signal is done by a Distortion meter b-wave analyzer.
Q2. An angle modulated signal with a sinusoidal carrier 100 cos Znfat and a sinusoidal message with frequency fa-20 Hz, knowing that -0.7, a) Draw the single sided spectrum b) Determine the modulated signal bandwidth. c) Determine the 70% and 90% bandwidth and transınitted power.
in FM , the maximum allowable frequency deviation is 4kHz and the frequency deviation by noise is 156.42HZ? then the signal to noise ratio is .......
Calculate a.) the cutoff frequency fc and b.) Vout at fc (Assume Vin = 10 Vp-p for all frequencies)
1. The Voltage spectrum of FM signal is shown in Figure 1. The maximum amplitude of modulating signal is 5V. Calculate the bandwidth , modulation index „Carrier frequency, modulating frequency and specify the type of Modulator(narrow band or wide band). 1.54 4.06 4.06 2.45 2.45 0.91 0.91 0.21 0.21 192 194 196 198 200 202 204 206 208 KHZ Figure 1 Reference: (1] Fundamental of Frequency modulation, Pages 150- 163, Principles of Electronics Communication system, Louis E. Frenzel Jr. Check Moodle assignment link for book. DFocus
A channel having a bandwidth of 1 kHz, the power of signal is 10 W and the power of noise is 5 W. Determine the channel capacity. Or: A channel having a bandwidth of 1 kHz and Signal to Noise Ratio (SNR) is 2. Determine the channel capacity.
How it is generated Single Sideband Modulator Using Filter Method
Question 4 (a) A carrier and a modulating signals are shown in Figure 2. Sketch and label the modulated output signal in time domain for: i. the Frequency Modulation (FM) i. the Phase Modulation (PM). Carrier signal Modulating signal Figure 2 (b) The FM and PM modulators parameters are shown in Table 1. Table 1 FM modulator Deviation sensitivity 6 kHz/v Carrier frequency = 400 kHz Modulating signal = sin (2n 4 kr) PM modulator Deviation sensitivity 1.6 rad/v Carrier frequency = 300 kHz Modulating signal = 1.25 sin (2n 5 kr) i. Calculate the modulation indexes for both modulators. i. Sketch and label the frequency spectrum for both modulators.
B- What is the difference between AM-DSB and AM-VSB.
Q2. For the scheme shown in Figure Q2, i. Draw the spectrum of the baseband signal (multiplexer output) for the multiplexer. ii. Determine the bandwidth of the baseband signal (multiplexer output) for the multiplexer. i. Determine the minimum transmission bandwidth of the multiplexer. Explain, briefly, the modification needed for the multiplexer in the figure to achieve this bandwidth. 4 kHz cos 10,000xt Basebund signal cos 24,000mt cos 2000mt cos 32,000nt Figure Q2
With the aid of diagrams, show and explain how phase locking is used to demodulate a frequency-modulated (FM) signal.
One input to a conventional AM modulator is a 600 kHz carrier with amplitude of 22 V. The second input is a 20 kHz modulating signal that is of sufficient amplitude to cause a change in the output wave of +9 V. Determine: a. Upper and lower side frequencies. b. Percent modulation. c. Peak amplitude of the modulated carrier and the upper and lower side frequency voltages. d. Maximum and minimum amplitudes of the envelope. e. Expression for the modulated wave. Then, f. Draw the output spectrum. g. Sketch the output envelope.