1. The Voltage spectrum of FM signal is shown in Figure 1. The maximum amplitude of modulating signal is sv. Calculate the bandwidth , modulation index Carrier frequency, modulating frequency and specify the type of Modulator(narrow band or wide band). 1.54 4.06 4.06 2.45 2.45 0.91 0.91 0.21 0.21 192 194 196 198 200 202 204 206 208 KHZ Figure 1

1. The Voltage spectrum of FM signal is shown in Figure 1. The maximum amplitude of modulating signal is sv. Calculate the bandwidth , modulation index Carrier frequency, modulating frequency and specify the type of Modulator(narrow band or wide band). 1.54 4.06 4.06 2.45 2.45 0.91 0.91 0.21 0.21 192 194 196 198 200 202 204 206 208 KHZ Figure 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Which statement is true? a. In FSK, the modulating signal and the carrier signal are both analog b. In FSK, the modulating signal and the modulated signala re both digital c. In FSK, the modulating signal and the modulated signal are both analog d. In FSK, the carrier signal is analog and the modulating signal is digital
TOPIC: AMPLITUDE MODULATION AND DEMODULATIONPlease answer this 2 question thanks.1. What is the different degree of modulation?2. What are the limitations of square law modulator?
A) what name the modulation scheme in the blue curve in A and C B) what is the duty cycle in B C) What is the sampling Frequency in B D) write and equation that represent the modulated signal in B solve all parts or will dislike
Q2/ One input to an AM DSBFC modulator is an 800 kHz carrier with an amplitude of 40 vp. The second input is a 25 kHz modulating signal whose amplitude is 1O vp. Determine a. Upper and lower side frequencies b. Modulation coefficient and percent modulation c. Maximum and minimum positive peak amplitude of the envelope d. Draw the output frequency spectrum e. Draw the envelope
1)to VRMs value to generate a signal with a peak voltage of 10 V with a signal generator in a multisim program..................... must be entered. 2)) the frequency of the signal generator to produce a signal with a period of 10ms...................... must be entered as. What should come to the dotted line?
A channel having a bandwidth of 1 kHz, the power of signal is 10 W and the power of noise is 5 W. Determine the channel capacity. Or: A channel having a bandwidth of 1 kHz and Signal to Noise Ratio (SNR) is 2. Determine the channel capacity.
Find the resonance point and the half-width of the speed versus frequency curve for the damped harmonic oscillator, under the action of a sinusoidal driving force. *It is all the data
1)(a) State advantages and disadvantages of AM and FM
In three-level PWM, the modulating process operates on each portion of the modulating function separately. The output peak value is still given by the depth of modulation, but the RMS value of the square wave is not Vin. Compute the THD for three-level PWM as a function of the depth of modulation (modulation index k).
Write the expression for the output voltage of a balanced modulator
In an Amplitude Modulator where the carrier and modulating signals are both sine waves, the frequency spectrum of the resulting AM signal is shown below. 12V 2V 2V kHz 803 808.6 a) Determine the equation of the modulating signal b) Calculate the bandwidth of the AM signal c) Calculate the effective current of the AM signal thru a 75-ohm load. d) Sketch the AM wave and label the maximum and minimum voltage of the signal.
Illustrate the basic concept of standard amplitude modulation.