Q1. The arms of a Porter governor areeach 250 mm long and pivoted onthe governor axis. The mass of eachball is 5 kg and the mass of thecentral sleeve is 30 kg. The radius ofrotation of the balls is 150 mm whenthe sleeve begins to rise and reachesto certain radius at maximum speed.The governor has radius that is 175mm at mid position. The speed rangeof the governor is 38 rpm, and theincrement in speeds is constant inthe three positions. Find : (1) thefriction of the load which existed atthe sleeve, and (2) the governorradius at maximum speed. The.friction is ignore in mid position only

Friction is the force resisting the relative motion of solid surfaces, fluid layers, and material…

Q1. The arms of a Porter governor are each 250 mm long and pivoted on the governor axis. The mass of each ball is 5 kg and the mass of the central sleeve is 30 kg. The radius of rotation of the balls is 150 mm when the sleeve begins to rise and reaches

Q1. The arms of a Porter governor are each 250 mm long and pivoted on the governor axis. The mass of each ball is 5 kg and the mass of the central sleeve is 30 kg. The radius of rotation of the balls is 150 mm when the sleeve begins to rise and reaches

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

water 3cm D=5 cm Mereury The tank in the has a 5 cm diameter plug at the bottom.on the rrght. All fluids are at zóc The Plag will pup out if the hydrestatic force is 30 for this condition what will be the readineg h ont Meicury mahometer on the left side2
Determine the resultant force of the water acting on the circular glass plate that Is to the side panel of the tank. Also, determine the location of the center of pressure along this inclined side, measured from the top. Question 2: FYw.h.A ate Fv= Yw.V 3 m radie 9810 Ixr x gate 9810 1 m 2 m Ma:0 Nar3- Fn 号×3-fvx3- -0 Ma=0-) NBx3- F t /2Fy-0 120° 3 m 1,- I,
Determine the magnitudes of the force Rand couple Mexerted by the nut and bolt on the loaded bracket at O to maintain equilibrium. 95 mm 155 mns 13 kN 18 kN :240 mrh Answers: R- 132 M-
5 ft 7.84 Find the smallest angle B for which the uniform crate can be tipped about corner A. Also compute the corresponding value of P oo o 5 ft 200 lb P 7.85 The belt is placed between two rollers whieh are free to rotate about A and B. Determine the smallest coefficient of static friction between the belt and the rollers for which the device is self-locking; that is, the belt cannot be pulled down for any value of P ooo o A As= 0.2 Fig. P7.84 Belt
4) While trying to change a tire, the driver shown below applies a force, P, of 25 Ibs at each end of the lug wrench. The lug wrench is made of solid steel with a circular cross-section of 0.5" and has a shear a) Use statics to calculate the amount of torque at point A of the wrench in Ib-in. Remember that the force is applied on both sides. [Ans. to Check: 450 lb-in] modulus of 11,400 ksi. c) The allowable shear stress in the wrench is 25 ksi. Determine the Factor of Safety (FOS) against yield. b) Calculate the maximum shear stress that the driver would apply to the lug nut at A (in ksi). [Ans. to check: 18.3ksi] d) Find the angle of twist in radians at the same location. Assume the wrench is symmetrical and that it is 9" from the center of the wrench to point A. 9.0 in. 9.0 in. A d = 0.5 in. P = 25 lb
* Find the Resultant Fore? if You Know → Fx₂ = 33.412 N F₁ duble F2 →F₂ Half of F3 ن الناس F3 4 SC F2
The ends of two fixed rods A and B are each made in the form of a single-threaded screw of mean radius 6 mm and pitch 2 mm. Rod A has a right-handed thread and rod B has a left-handed thread. The coefficient of static friction between the rods and the threaded sleeve is 0.12. Determine the magnitude of the couple that must be applied to the sleeve in order to draw the rods closer together. A B 2 kN 2 kN
من هم سدفة فلیصلی علی H.WD A Solid steel bar of dlameter 60mm and length 350 mm is Placed inside analuminum cylinder of Inside diameter Fomm ard out side dlameter lomm, a comressive lood of looo la is appliel on the assembly, find the stresses in the bar and the cylinder? take Est = 200GPa and EAI = F0 G Va. Cover Plate te.25mm d- do 35omm Alum. cylinder Strel Aoayr مرّر للأعلى لاستعراض الفلاتر + إضافة شرح. . . mum <
TWO CONCRETE BLOCKS WEIGHING 1800 N EACH FORM PART OF THE RETAINING WALL OF A SWIMMING POOL. WILL THE BLOCKS BE IN EQUILIBRIUM WHEN THE POOL IS FILLED, AND THE POOL EXERTS THE LINE LOADING SHOWN? IF YES, WILL IT SLIDE OR TIP? ALSO, DETERMINE THE HEIGHT OF WATER IN WHICH THE POOL WILL BE FILLED SUCH THAT THE BLOCKS WILL BE IN EQILIBRIUM. 300 mm 540 mm A-0.5 540 Plastic liner mm A-10 6Nmm
The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD, a 15- mm diameter 304 stainless steel rod EF, and a rigid bar G. 1) If P=5KN, determine the horizontal displacement of end F of rod EF 2) If the horizontal displacement of end F of rod EF is 0.45 mm, determine the magnitude of P. -300 mm- 450 mm- Figure 3: Assembly 4P
47 H.WOA rod Consists of three bars af unequal dlameters as shown in fig., find the Stress in each bar and the C longation of the rood ?_use E= 200GPA %3D =30mm =20 mm 1.5m 2.5m 2m
In Fipure , with its dimensions, loadinp Status and material properties,different full circle cross -sec¥ion rod has been piven. The AB part Of the rod is steel, 100mm in diameter; BE part is COpper and i diameter. It Is 80 mm - Draw the Force Diaprom Of the Bar Calculate +he Normol stresses that will occur in parts AB and BC. Calcu late the total lenpht chanpe of the rodi 179 86 Material ECM Pa) (Copper) steel 210000 (steel) Copper 100000 120 cm 110cm