Q1 The curved portion of the bar shown has an inner radius of 20 mm. Knowing that the allowable stress in the bar is 150 MPa, determine the largest permissible distance (a) from the line of action of the 3-kN force to the vertical plane containing the center of curvature of the bar. r = 20 mm. Sha IP = 3 kN 25 mm 25 mm Activ

Q1 The curved portion of the bar shown has an inner radius of 20 mm. Knowing that the allowable stress in the bar is 150 MPa, determine the largest permissible distance (a) from the line of action of the 3-kN force to the vertical plane containing the center of curvature of the bar. r = 20 mm. Sha IP = 3 kN 25 mm 25 mm Activ

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM 2: The retangular plate is deformed into the shape of a rhombus shown by the dashed line Deteminethe average shear strain at corner A with respect tothex and y axis. mm D 400 mm В A 14 mm - 300 mm-
The bar ABC is supported by a pin at A and a steel wire at B. Determine the magnitudeof force Pinlbif the elongation of the wire is 0.059 in. The cross-sectional area of the wire is 0.0039 inandthemodulus of elasticity of steel is 29001 ksi,X=3.86 ft, Y = 6.78 ft, and L = 5.6 ft. Express the final answer to four decimal places. ... B Y
Rod BD is made of steel (E = 29 × 106 psi) and is used to brace the axially compressed member ABC. The maximum force that can be developed in member BD is 0.02P. If the stress must not exceed 18 ksi and the maximum change in length of BD must not exceed 0.001 times the length of ABC, determine the smallest-diameter rod that can be used for member BD. Take P = 148 kips.The smallest-diameter rod that can be used for member BD is in.
The homogeneous wire ABCD is bent as shown and is attached to a hinge at C. Determine the length L that results in portion BCD of the wire being horizontal. 200 mm -L- В D IC 150 mm A
3. The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminum and bronze. Determine the vertical displacement of the point where the force P = 10 kips is applied. Neglect the weights of the members. Aluminum L= 4 f A=0.75 in. E= 10x 10 psi B 4 ft Bronze L= 5 A A=0.25 in.? E= 12x 10 psi 2 ft--2 ft-→
Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P 5 kip are applied to the lever arm, Determine (a) the reactions at the fixed supports A and C and (b) the shear stress developed at a point located 1 in. from the center-line of the bar at a cross-section close to point A. 2.5 f 2.5 ft E 6ft 4 in. 4 in.
q1 The steel block shown in is subjected to a compressive force on all directions. Determine the change in length of Z-direction if the change in length of Y- direction is (-1.3mm). E for steel =210*10° N/mm? and u=0.28). 20cm 10cm F Scm F
The cross-sectional area of the bar ABCD is 600 mm². Determine the maximum normal stress in the bar?
The aluminum block has a rectangular cross section and is subjected to an axial compressive force of 36 kN. If the 37 mm side changed its length to 37,5033 mm, determine Poisson's ratio and the new length of the 50 mm side. Ea-70 GPa. 36 kN- 37 mm 50 mm 36 kN 75 mm.
The T-bracket is formed by welding together two cylindrical rods AB and CD. If the allowable shear stress is 80 MPa, what is the smallest allowable diameter of rod AB? Neglect the stress caused by the transverse shear force
1200 N 2. For the bone shown to the left, assume the cross-section at C can be approximated as annular, with an outer diameter of 25mm. When the 1200 N forces are applied, the average normal stress in the bone at point C is determined to be 3.80 MPa. Determine the inner diameter of the bone cross section at C. Ans: d; = 14.93 mm 4 in. P 3 in. B 1200 N "UI 8
Two cylindrical rods, one of steel and the other of brass, are joined at C and Q1) restrained by rigid support at 4. There is a gap of 1 mm between end E and rigid support at right side. For the loading shown and knowing that E; = 200 GPa, E = 105 GPa, as = 13×106 1/°C and as = 19×10-6 1/°C, determine the minimum change in temperature to close the gap. Dimensions in mm 100 100 F180- 120- A D Brass Steel Be 60 kN 40 kN 20-mm diam. 10-mm diam.