Q1] The CT signal x(t) = 10cos4(5000πt) is applied to the input of the PCM system, and it is oversampled by 50%. The SNqR = 30 dB. Find the following: (a) The frequencies in x(t), and then draw its spectrum. (b) The value of the sampling frequency, and the specifications of the LPF to select only the first copy at the output of the sampler. (c) The number of quantization levels, and the bit rate of the PCM signal. (d) The minimum bandwidth of the channel to transmit the PCM signal without distortion.

Q1] The CT signal x(t) = 10cos4(5000πt) is applied to the input of the PCM system, and it is oversampled by 50%. The SNqR = 30 dB. Find the following: (a) The frequencies in x(t), and then draw its spectrum. (b) The value of the sampling frequency, and the specifications of the LPF to select only the first copy at the output of the sampler. (c) The number of quantization levels, and the bit rate of the PCM signal. (d) The minimum bandwidth of the channel to transmit the PCM signal without distortion.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

[Q1] Assume there are 50 signals, each one is band-limited to 10kHz and sampled at a rate 28% over the Nyquist rate. Assuming these signals have the same voltage range, the samples of each signal are quantized with the maximum quantization error is 0.31% of the peak amplitude. The quantized samples are coded to be binary using PCM. The binary bits from each signal are multiplexed using TDM-PCM. Determine the channel bandwidth required to transmit the multiplexed signal.
A PM signal has a maximum allowed deviation of 17 kHz, and an actual deviation of 8 kHz. What is thepercentage modulation?
The AM signal has total power (66W) and PSSB-sc (8W), 1- Compute the Vc, Vm and modulation index. 2- Sketch the AM signal in time and frequency domain. The thermal
What is the purpose of low pass filtering a PWM source? To minimise noise produced by the PWM pulses To improve PWM efficiency To increase the amplitude of the PWM signal To rectify the PWM signal
After getting the formula of FM and PM moducation signal, how can I sketch this one.
3.) Determine the band width and baud for an FSK Signal with a mark frequency off99 kH2), aspace frequency of (2°1KHZ). and abit vate of lokbps).
How are: a) FM signal is generated b) PM signal is generated c) Angle Modulated signal is demodulated
determine nyquist Sampling rate and Nyquist Sampling interwal for The Signal se sine (1000at)
[Q2] Illustrate the signal waveforms of PAM, PWM, and PPM in simple drawings. [Q3] Suppose (t) has the spectrum in the figure below, where f = 550kHz and € = 460kHz. Sketch Xs(f) for f. = 1.6MHz if ideal sampling is considered. X(f) AÏN -f f₁ + E 0 fu
Q36)The signal can be reconstructed from its samlpes a. None of the mentioned b. Above Nyquist rate c. At & above the Nyquist rate d. At Nyquist rate This multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer.
ii. An LVDT has a maximum core motion of ±1.5 cm with a linearity of ±0.3 % over that range. The transfer function is 23.8 mV/mm. If it is used to track a motion from -1.2 cm to +1.4 cm, what is the expected output voltage? Further, calculate the maximum linearity deviation of the transfer function.
A specific waveform of EEG signal comprises a frequency range up to 200 Hz. What is the minimum sampling rate in order to fully reconstruct such a signal?