Q1 rad The angular velocity of link AB is wAB = 10 . Determine the velocity of block C and the angular velocity of link BC at the instant 0 = 60° and Ø= 45°. Show the free body diagram for each link. 4 m WAB= 10 rad/s BO 3 m

Q: PROVIDE DIFFERENT ACCESSORIES IN SHAPER MACHINE WORKS VERTICAL AND HORIZONTAL WITH PICTURE

A: Shaper machine is a cutting machine that converts reciprocating motion of a flywheel into linear…

Q: what is the speed ratio of v/U for part b?

A:

Q: Define Straddle hubs.

A: A straddle is a trading strategy that involves options.

Q: 3 50mm link is fixed, the number of finks can rotate fuy filly that

A: Given data: Let 4 links;s=100 mmp=200mmq=300mml=350mmas shown in fig. if 350 mm is fixed  then  no.…

Q: Write a note on different types of gear along with application.

A: The gears are used for power or torque transmission. They are generally used whenever the positive…

Q: Write about characteristics of gyroscope with a neat sketch.

A: The answer is in next steps

Q: 2 cosh(lnx)

A: to find: 2cosh(lnx)

Q: With neat sketches explain the hydraulic quick return mechanism used on a shaper?

A: Hydraulic mechanism :- This mechanism are suitable increasingly popular these day as of their bigger…

Q: differentiate between shaper and planer machine any six difference

A: A shaper is a reciprocating type machine used to produce horizontal, vertical, and inclined surfaces…

Q: What part of an engine or Turret lathe slides move in the direction normal to the beds Ways

A: Given:- Turret lathe To find:- The part that moves in the direction normal to the bed of the bed

Q: Why is the pressure during cylinder retraction greater than that required for extension?

A: Given that the pressure in retraction is greater than extension

Q: If a wrench is unable to loosen a wheel nut, what are two ways that you could increase the torque…

A: There are two ways to increase the Torque if a unable to loose the wheel nut

Q: Worm gearboxes are often just called “speed reducers”, why?

A: Worm gear drive are one of the best gear drive to reduce the speed. Worm gear box consists of a…

Q: for velocity one find the total gear ratio and not velocity

A: the output speed is:Here negative sign is just indicating the opposite direction of the rotations of…

Q: v thread is:

A: In screw largest diameter is its major diameter

Q: The explantion is not clear

A: given : height of channel h = 10m width of channel w= 34m angle made by channel θ= 15o to find:…

Q: Read through the following chronological instructions. Choose the correct figure that best matches…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: Why it is important to loosen one screw before tightening the opposing one by an equal amount?

A: If there are two sequences of screws or bolts and n number of screws is to be tightened on each…

Q: The rotation angle of the joints is still needed.

A:

Q: Explain rotating a wheel.

A: The motion of a circular object rotating around its axis is referred to as rotating a wheel. The…

Q: Mom and vibrations c) Explain why the wheel/tire balancing is necessary

A: Balancing: When there is no net couple and force during static and dynamic condition of the vehicle…

Q: Name the 2 types of axial loading?

A: Two types of axial loading are tensile and compressive stress. Both kinds of stresses arise within…

Q: what is the equation of the addendum and dedendum in bevel gear

A: Equation for addendum is ab=1Pwhereab=addendum of bevel gearP=Diametral pitch

Q: What is the reason qhy HRSG HP, IP & LP drum separate from wet of ground using a wooden support…

A: 1. HRSG HP Drum (High-Pressure Drum) Separation from Wet Ground using Wooden Support :   To prevent…

Q: What makes new gear special?

A: Given data:- Gear:-A gear is a mechanical device that connects two rotating shafts by transmitting…

Q: the main diference between the prick punch and center punch?

A: Prick punch is a mechanical tool, which is made up of steel and it is used to mark points on the…

Q: Elaborate which balancing method is performed for wheel/tire balancing process over there and give…

A: wheel or Tyre balancing :-

Q: B. A machine - part needs 14 bolts a How many bo43 are needed For 25 nachine -parts? b. wnat is the…

A:

Q: d rotation speed aff

A: Required 1. ) Effect of weight on drilling ? 2) rotation speed on drilling ?

Q: What are two reasons gears are used for?

A: Reasons for gear: There are many practical reasons are available for gears used in industry.