Q#01: The schematic shown in figure below is for Divide_by_11, a frequency divider, that divides clk by 11 and asserts its output for one cycle. The unit consists of a chain toggle-type flip-flops with additional logic to form an output pulse every 11th pulse of clk. The asynchronous signal rst is active-low and drives Q to 1. Develop and verify a model of Divide_by_11. Vcc clk clk clk dk clk rst rst rst rst w1 w2 T clk QB cik_by_11 rst rst

Q#01: The schematic shown in figure below is for Divide_by_11, a frequency divider, that divides clk by 11 and asserts its output for one cycle. The unit consists of a chain toggle-type flip-flops with additional logic to form an output pulse every 11th pulse of clk. The asynchronous signal rst is active-low and drives Q to 1. Develop and verify a model of Divide_by_11. Vcc clk clk clk dk clk rst rst rst rst w1 w2 T clk QB cik_by_11 rst rst

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

To reset IC chips in a system at power-on, the chips must be powered on and working already. That is to say that the reset signal needs to be after the power-on time. Assume that you need to generate a reset signal 1 ms after power-on using an RC circuit, what will be roughly the values of the resistor and capacitor?
Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (WO-W9) with one terminal connected to Vec. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with “a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f a a e
Draw logic diagram for half adder and full adder circuit using Logisim Software
III) Convert from Hexadecimal to Decimal (a) 1ACED716 (b) C1AC18A.E8B916 IV) Convert Decimal to Hexadecimal (a) 114510 (b) 3176.5410
Draw the schematic of a modulo-6 syncrhonous counter (counting sequence is 010, 110, ...). The counter has the following features: Asynchronous Reset is Active High A value D can be loaded into the counter, using the Load signal, which is Active Low.
How many states the PN sequence generator of DB20 have? • What is the length of PN sequence generator of DB20? • Calculate the outputs of each clock and put them on the Table (2). • What is the PN Sequence of the DB20. • Verify the outputs you get with the outputs from the device.
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
TRUE or FALSE 9. A waveform can be enabled or disabled by both AND and OR gates. 10. An exclusive-OR gate output is HIGH when the inputs are unequal.
Design a combinational circuit that takes 3-bit pattern as input and outputs binary code of bit position of the first 1' in the pattern reading from MSB (2nd position) to LSB (0th position).An additional output variable V is required along with binary code to indicate that the binary code is valid or note i.e., if the input pattern is '000' then the output V should be '0' to indicate that the binary code is not indicating the bit position of first 1' and we don't care about the binary code if V = 0. Design the required circuit using dual 4x1 MUXS and minimum additional logic.Available resources along with dual 4x1 MUXS are NOT gates, 2-input(AND, OR, NAND, NOR) gates.
Write an assembly 8051 code to count a hexadecimal digit every second and display it on the 7-segment.
Develop the Q output waveforms for a 74HC190 up/down counter with the input waveforms shown in figure below. A binary 0 is on the data inputs. Start with a count of 0000. CLK CTEN LOAD
A 9-bit asynchronous counter has a 128-kHz clock signal applied. (1) What is the MOD number of this counter? MOD number = (ii) What will be the frequency at the MSB output? fmsb = (iii) Assume that the counter starts at zero. What will be the count after 635 input pulses? After 635 input pulse, Count =