Q.3. (30%) A circular aluminum tube subjected to T pure torsion by torques T has an outer radius r2 equal to 2 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 500x10-6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist (0) is 0.15°/m and the maximum shear strain is to be kept at 500x10-6 rad by adjusting the torque T, what is the minimum required outer radius (r2 )min?

Q.3. (30%) A circular aluminum tube subjected to T pure torsion by torques T has an outer radius r2 equal to 2 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 500x10-6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist (0) is 0.15°/m and the maximum shear strain is to be kept at 500x10-6 rad by adjusting the torque T, what is the minimum required outer radius (r2 )min?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.3P: Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2...

See similar textbooks

Similar questions

AN ALUMINUM TUBE IS FASTENED BETWEEN A STEEL ROD AND BRONZE ROD AS SHOWN IN THE FIGURE. AXIAL LOADS ARE APPLIED AT THE POSITIONS INDICATED. FIND THE VALUE OF P THAT WILL NOT EXCEED A MAXIMUM OVERALL DEFORMATION OF 5mm OR A STRESS IN THE STEEL OF 120MPa, IN BRONZE OF 130 MPa AND IN ALUMINUM OF 90 MPa. Modulus of Elasticty of Bronze = 80 GPa, Aluminum = 65 GPa and Steel = 210 GPa. 2P P 3P 4P L = 500mm 800 A = 400mm² 900 600 700 C
The aluminum rod AD (E=73 GPa, a=23x10-6/°C) has a diameter of 15 mm and is attached to the rigid support at A when the temperature T1 = 30°C. If the temperature becomes T2 = -20°C, and the axial loads are applied to the rod as shown, determine: a) The location and magnitude of the maximum stress acting on the rod AD b) Displacement of point D c) Average strain in part BC 5 kN A +7 kN - 5 kN в C D 1400 mm- 1300 mm- 1500 mm-
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D What is the axial stress o Ag in Pa? 10KN 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
A circular aluminum tube subjected to pure torsion by torque T (see figure) has an outer radius r, equal to 1.5 times the inner radius r,. T (a) If the maximum shear strain in the tube is measured as 460 x 10-° rad, what is the shear strain y, (in radians) at the inner surface? rad (b) If the maximum allowable rate of twist is 0.126°/m and the maximum shear strain is to be kept at 460 x 10-6 rad by adjusting the torque T, what is the minimum required outer radius (r..min' in mm)? mm
A 3m long steel plate having a cross section of 25mm by 300mm is use as a hanger and subjectedto a tensile load of 1070 kN. The proportional limit of the steel is assumed to be 200 MPa. If thePoisson’s ratio is 0.25, determine the following;a. The transverse strain,b. The total axial deformation, andc. The transverse dimensional change along 300mm.
A small aluminum alloy [E = 61 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 155 mm. The cross-sectional dimensions of the tee shape are b %3D = 22 mm, d = 33 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a %3D compressive normal strain of 420 µɛ is measured from a strain gage located at c = 6 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P В D E Strain gage- d H b Answer: P = i N
Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
Q- A stepped steel shaft is subjected to a clockwise torque of 10 Nm at its free end. Shear modulus of steel is 80 GPa. Find the strain energy in the shaft? A 50 mm dia 100 mm B 25 mm dia 100 mm C K T=10 Nm
For the cantilever beam shown in Figure 4, a) Determine the maximum shear stress on the beam. State exactly what location on the beam and where on the cross-section this maximum shear stress occurs. b) If the beam is fabricated from one structural tee and a plate using fasteners at point A (shown in the cross-section) and the spacing between the fasteners along the beam is 100 mm, determine the minimum shear strength of each fastener in kN. c) Determine the state of stress at point B (on the web just below the flange), on the cross-sectional cut located just to the left of the fixed support (connection). Sketch the result. d) For point B, determine the principal stresses, the maximum in-plane shear stress and their orientations. Sketch the results. 50 kN 0.5 m Fixed Connection 100→ 200 All dimensions in mm
what differ between plane stress and strain.As like pancel is which of those? （eg,a pancil ,glass normal face or glass side face)
An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 1) What is the deformation 8Ag in mm? 10KN 0.8m 0.4m 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
1. Calculate the strain at the centroid of the tension steel in single layer if the effective depth is 250 mm and the depth of neutral axis is 100 mm. answer: 0.0045 2. Calculate the strain at extreme layer of steel if fy=415 MPa and the strength reduction factor is 0.80. answer: 0.0038