Q.1. Two flat plates are oriented parallel above a fixed lower plate as shown in figure below. The top plate, located a distance b above the fixed plate, is pulled along with speed V. The other thin plate is located a distance cb, where 0 c 1, above the fixed plate. This plate moves with speed VI, which is determined by the viscous shear forces imposed on it by the fluids on its top and bottom. The fluid on the top is twice as viscous as that on the bottom. Plot the ratio V1/V as a function of c for 0

Q.1. Two flat plates are oriented parallel above a fixed lower plate as shown in figure below. The top plate, located a distance b above the fixed plate, is pulled along with speed V. The other thin plate is located a distance cb, where 0 c 1, above the fixed plate. This plate moves with speed VI, which is determined by the viscous shear forces imposed on it by the fluids on its top and bottom. The fluid on the top is twice as viscous as that on the bottom. Plot the ratio V1/V as a function of c for 0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A thin plate is pulled at a speed V through a small gap of hieht h as shown in figure below. The space on both sides of the plate contains different types of fluids. Fixed wall Oil ul Plate h V (m/s) Oil p2 Fixed wall HHHHHHHHHHJ Prove that the postion of the plate y takes the form: u,h i. y= (H +H2) When the shear forces are equal on the both sides of the palte. hyu1 Wuit/u2) ii. y = When the drage force is minimum.
A thin plate is pulled at a speed V through a small gap of hieht h as shown in figure below. The space on both sides of the plate contains different types of fluids. Fixed wall Oil u1 Plate V (m/s) Oil u2 Fixed wall Prove that the postion of the plate y takes the form: H,h (H, + H2) i. y= When the shear forces are equal on the both sides of the palte. h/u1 ii. y = When the drage force is minimum.
Two flat parallel plates are separated by a small gap h filled with an incompressible fluid of viscosity u. Assume that the length and width of the plates to be much larger than the gap h. The top plate moves horizontally with a velocity V while the bottom plate is held stationary. The magnitude of the difference between the shear stress at the top and bottom walls is found to be At. Velocity of the top plate is?
1. The velocity distribution for the flow of a Newtonian fluid between two fixed wide, parallel plates (see Fig.) is given by the equation: 3V 3/[ ₁ - (-)*] where V is mean velocity. The fluid has viscosity of 0.04 lb.s/ft2. Also, V = 2 ft/s and h = 0.2 in. Determine: U = (a) the shearing stress acting on the bottom wall and (b) the shearing stress acting on a plane parallel to the walls and passing through the centerline (midplane).
A segment of a generator shaft is subjected to a torque T and an axial force P, as shown in the figure. The shaft is hollow (outer diameter d, = 295 mm and inner diameter d, = 250 mm) and delivers 1,700 kW at 4.0 Hz. If the compressive force P = 600 kN, what are the maximum tensile, compressive, and shear stresses in the shaft? (Enter the magnitudes in MPa. Assume that the structure behaves linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain e resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) maximum tensile stress 676 X MPa maximum compressive stress 31461.087 X MPa maximum shear stress 277.126 X MPa Construct a clear sketch of Mohr's circle for this problem, and construct a sketch of the stresses on properly oriented elements for your above solutions, clearly indicating the orientation wrt the base x-y coordinate system (as demonstrated in the lectures). Submit…
A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum rod (2) that has a 2 in. diameter and a solid aluminum rod (3) that has a 1.375 in. diameter [Est =30,000 ksi, Eat =10,000 ksi]. The bar is loaded as shown in figure below, Determine: (1) the displacement of point D with respect to the fixed support at A. (2) the maximum normal stress in the entire axial assembly. (3) the normal strain in the steel tube (1). 34 kips 18 kips 25 kips (1) (2) (3) D B 34 kips 18 kips 60 in. 40 in. 30 in.
The beam AB shown in the figure supports a uniform load of intensity 3000 N/m acting all over half the length of the beam. The beam rests on a foundation that produces a uniformly distributed load W over the entire length. 3000 N/m B w N/m 0.8 m 1.6 m 0.8 m 3.2m O Compute the value of W to be in equilibrium. Compute the max. shear force of the beam. Compute the max. m-ment of the beam.
Hydrostatic forces on inclined plane surface 6Q. A rectangular gate having a width of 4 ft is located in the sloping side of a tank as shown in the figure. The gate is hinged along its top edge and is held in position by the force P. Neglect the friction at the hinge and weight of the gate. Determine the required value of P. V Water Hinge Gate 60° 6 ft 10 ft
120MPA 40MPA QUESTION 5) Two elastic bodies made of different materials are placed in a rigid cavity and their surfaces are in full contact. In the vertical direction, a uniform pressure force acts on body 1 with 120MPA and on body 2 with 40MPA. Calculate all the stresses in objects 1 and 2 and the length changes in the z-axis direction. 1) 2 50cm ///// TT// 60cm 60cm Elasticity modules: E1 =180GPA, E2 =100GPA 55cm Poisson ratios: V1 =0.4, v 2=0.2
In the figure below, the beam is cantilevered from the wall. The connection of the beam to the wall can be considered a general interaction. The beam has a uniform density, so it will be subject to a weight force applied mid-way between points A and B. length from point A to point B =10.0 meters; weight applied at point B = 1.00 kN; beam weight = 0.500 kN Beam embeded in cwalla cautilever B A What is the magnitude and direction (relative to the x-y coordinate system shown in the upper left portion of the figure) of the horizontal and vertical components of the wall support? horizontal = 0 N, vertical = 1.50 kN O horizontal = 1.50 kN, vertical = 0N O horizonatl = O N, vertical = 1.00 kN O horizontal = ON, verttical = 2.00 kN
3) Solve the following problem: The hollow tube ABCDE is made of a material that is subjected to five torsores that act as shown in the figure below. The outside diameter of the tube is d2 = 1.0 inches. The maximum allowable shear stress is 12,000 psi (12,000 lb / inch ^ 2). In addition, the maximum rotation per foot allowed is 2.0 degrees (2.0 degrees / foot). Take G = 9500 Ksi (9,500,000 psi). Note: Remember that 1 degree equals 0.0175 radians. Determine the maximum internal diameter d1, allowed for the tube.
The pressure drop ΔP = P1 − P2 through a long section of round pipe can be written in terms of the shear stress ?w along the wall. Shown in Fig is the shear stress acting by the wall on the fluid. The shaded region is a control volume composed of the fluid in the pipe between axial locations 1 and 2. There are two dimensionless parameters related to the pressure drop: the Euler number Eu and the Darcy friction factor f. (a) Using the control volume sketched in Fig. , generate a relationship for f in terms of Eu (and any other properties or parameters in the problem as needed). (b) Using the experimental data and conditions of Prob. 7–81 (Table P7–81), plot the Darcy friction factor as a function of Re. Does f show Reynolds number independence at large values of Re? If so, what is the value of f at very high Re? Answers: (a) f = 2 D LEu; (b) yes, 0.0487