Q.06. Beam ABCD represents a reinforced-concrete foundation beam that supports a uniform load of intensity q1 = 3500 lb/ft (see figure). Assume that the soil pressure on the underside of the beam is uniformly distributed with intensity q2. Calculate q2 and draw the shear and moment diagram of the foundation beam. 91 = 3500 lb/ft В A D tsond 92 - 3.0 ft-→- +-3.0 ft 8.0 ft

Q.06. Beam ABCD represents a reinforced-concrete foundation beam that supports a uniform load of intensity q1 = 3500 lb/ft (see figure). Assume that the soil pressure on the underside of the beam is uniformly distributed with intensity q2. Calculate q2 and draw the shear and moment diagram of the foundation beam. 91 = 3500 lb/ft В A D tsond 92 - 3.0 ft-→- +-3.0 ft 8.0 ft

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

BRAIN EXERCISE PROBLEM 1 Determine the maximum shear stress and the maximum flexural stress of the beam. The cross-section of the beam is 150 mm x 350 mm. A B 10 KN 15 KN/m C 1.50 1.00 1.50 10 KN/m D D.Lopez 2.00 in meters Figure A: Overhanging Beam E
The T section is shown in Figure below is the cross-section of a beam. The beam is subjected to a uniform distributed load = 4 kN/m. The N.A is located at 34.7 mm from the bottom and that IxA =10.64x106 mm. Determine (a) the maximum shearing suess (b) the shearing stress at 15 mm from the bottom face. Q2 %3D 20mm 4 kN/m 120mm A 34.7 mm 20mm lm 3m 1m 220mm TT
Which of the following best give the value of the lateral torsional modification factor, Cb, of the figure shown. M 12.5Mmax C = 2.5Mmax+3MA + 4MB + 3Mc тах ) 1.67 1.0 2.27 O 1.5
• A two-span continuous one-way slab with span length of 4.3 meters is integral with its beam supports which are 300 mm wide with spacing 2m on center. The slab carries a factored load of 27000 Pa. f'c = 21Mpa and fy = 275 Mpa. a. Determine the minimum depth of slab (mm). b. Compute the positive and negative factored bending moments (KN-m). c. Calculate the spacing of 10mm main bars (mm). d. Find the spacing of 10mm temperature bars (mm).
A roadway sign weighs 7.2 kN and is supported by a structural pipe that has an outside diameter of 250 mm and a wall thickness of 11 mm. The resultant force of the wind pressure acting on the sign is 9 kN, as shown. Assume a = 8.2 m, b = 3 m, Pz = 9 kN, and %3D Py = 7.2 kN. (a) Determine the normal and shear stresses oH, TxyH at point H. (b) Determine the normal and shear stresses OK, TyzK at point K. a H K Answers: OH = i MPа. TxyH 28.6 MPa. OK i MPа. TyzK i ! MPa. II
The beam shown carries a concentrated load P = 12 kN and a uniformly distributed load w. 225 N/m. The dimensions a, b, and c are 1.0 m, 1.2 m and 1.4 m, respectively. If the beam is a 50 mm x 100 mm x 3 mm hollow tube (b x h x t), determine the maximum bending stress, the maximum vertical shear stress, and the deflection under the load P. Wo
SHEAR STRESS 2 If the T-beam is subjected to a vertical shear of V = 60 kN, determine the maximum shear stress in the beam. Also, compute the shear-stress jump at the flange-web junction AB. Sketch the variation of the shear-stress intensity over the entire cross section. VQ TBI = It (60 kN)Q 100 mm 100 mm 75 mm 100 mm I(300) B' VQ TR = It VQ B 150 mm I(100) V = 60 kN
CLO 1: Determine the maximum shear stress in MPa if P = 115 kN. 20 mm 25 mm 20 mm 3somm 28.395 O 72.282 32.467 21.550 45mm
BRAIN EXERCISE PROBLEM 1 Determine the maximum shear stress, maximum flexural tensile stress and maximum flexural compressive stress of the beam. The dimensions of the cross-section of the beam are a = 300 mm, b = 150 mm and c = 50 mm. A 30 KN/m D. Lopez www. 10 KN 2.00 B C 20 KN/m D wwwww. 1.00 1.00 2.00 in meters E Figure A: Overhanging Beam C a
Problem Given: • cantilever beam, fixed support at A • W = 15 kN/m • L=6m . El = constant Determine the following: 1. deflection at B 2. slope at B 3. deflection at midspan W L
Q3 50 kN 5 m 5 m. 3々 Analyze the above symmetrical otructure under the given symmetrical loading by using force mefhod
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4