AB3 m1.5 mA. Draw the shear force and the bending moment diagrams, V and M for the simplysupported beam under the given loading condition.B. If the beam is subjected to the internal moment of M forming an angle of 600 with thehorizontal z axis as shown in the beam cross section, determine the maximum bendingstresses acting over the cross section (at points A and B) and the orientation of theneutral axis.Beam cross sectionMy100 mm60M100 mm50 mm12 kN/mA50 mm200 mm2.60°BA

Given angle = 60 deg UDl = 12kn/m

B 3 m 1.5 m A. Draw the shear force and the bending moment diagrams, V and M for the simply supported beam under the given loading condition. B. If the beam is subjected to the internal moment of M forming an angle of 60⁰ with the horizontal z axis as shown in the beam cross section, determine the maximum bending stresses acting over the cross section (at points A and B) and the orientation of the neutral axis. Beam cross section M A 100 mm z-ft 60° 60 M 100 mm 12 kN/m A 50 mm 200 mm

B 3 m 1.5 m A. Draw the shear force and the bending moment diagrams, V and M for the simply supported beam under the given loading condition. B. If the beam is subjected to the internal moment of M forming an angle of 60⁰ with the horizontal z axis as shown in the beam cross section, determine the maximum bending stresses acting over the cross section (at points A and B) and the orientation of the neutral axis. Beam cross section M A 100 mm z-ft 60° 60 M 100 mm 12 kN/m A 50 mm 200 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3. A beam is subjected to the variable loading shown. Calculate the support reactions at A and B. w 2400 N/m | w = wo-kx³ 6m 1200 N/m 111x B
Consider the simply supported beam shown below. L= 3m, w= 12kN/m, E= 180GPa, I = 140(10)^6 mm^4. Determine the following: A B |- -1 a. The maximum moment in the beam in kN-m b. The deflection at B in mm c. The location of maximum deflection measured from A in meters d. The maximum deflection of the beam in mm W C
265 Determine and locate the resultant of the two nt 0 forces. acting on the I-beamn. 3 m Problem 2/65
CLO 3: An 8-m simply supported beam AB carries a downward 8- kN point load located 6 m from the left support A. Determine the value of constant of integration, c2. -35/EI -40/EI -20/EI
calculate the location of the centroid, the second moments and product of area for the cross- section if; D = 67 mm, B = 41 mm & t = 2.41 mm A L Test beam A Strain gauge W (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 Strain gauge 2 b Strain gauge 3 a B (b) Location of Huggenberger strain gauges From these, calculate the orientation and position of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis).
7-1. If the wide-flange beam is subjected to a shear of V = 20 kN, determine the shear stress on the web at A. Indicate the shear-stress components on a volume element located at this point. 200 mm 20 mm B 200 mm -20 mm 300 mm 20 mm
(c) The slope and displacement on the I-Beam is developed due to the uniform distributedload along span AB. The elastic modulus and moment of inertia of the I-Beam is 200GPa and 360xl06 mm4, respectively. i) Establish the real moment equation for the I-Beam.ii) Establish the virtual moment equation for the I-Beam.iii) Determine the slope and displacement at A using Unit Load Equation.
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 0=15⁰ a=3m b=3m c= 5m 5 panels@(a)m each F E b G B b b C a Q Zoom image Compute the force on member CL P
7-1. If the wide-flange beam is subjected to a shear of V = 20 kN, determine the shear stress on the web at A. Indicate the shear stress components on a volume element located at this point. Prob. 7-1 200 mm A 20 mm B 20 mm 300 mm 200 mm 20 mm
Determine the vertical force P which must be applied at G so that the linkage is in equilibrium for the position shown. 125 mm 300 mm C 125 mm 9 N-m B 180 N 250 mm F. G 100 mm 100 mm
5. THIS IS FOR EXTRA CREDIT. Determine (a) the equations of the shear and bending- moment curves for the beam and loading shown, (b) the maximum absolute value of the bending moment in the beam. w=wo (1-²)
The symmetrical beam cross-section shown is loaded by a transverse shear force V 25 kip. Calculate the maximum transverse shear stress acting on the sec- tion. ΝΑ -+-1 in.|-- H V 6 in. 1 in. - 1 in.|-—_ 6 in.