Q. NO.1: Determine the real and reactive power loss in the line, where the line impedance is 0.01X+j0.5X Q,The line is connected by two single-phase ideal voltage sources V1 and V2. Also determine the complex power for each and find whether they are delivering or receiving reactive and real power. 0.01x + j0.5X I12 10X 4 15° v | 15X z0° v

Q. NO.1: Determine the real and reactive power loss in the line, where the line impedance is 0.01X+j0.5X Q,The line is connected by two single-phase ideal voltage sources V1 and V2. Also determine the complex power for each and find whether they are delivering or receiving reactive and real power. 0.01x + j0.5X I12 10X 4 15° v | 15X z0° v

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.11P

See similar textbooks

Similar questions

The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. Use Gauss-Seidel method in Matlab to analyze the system the tolerance of error is 10-3. Then anwser the questions as follows. V, = 1.05200 0.01+ j0.025 300 + j200 MVA 0.015 + j0.035 150 MW 200 +j150 MVA 0.01+ j0.03 |V = 1.03 The admittance matrix (Y_bus)? 0.02 + jo.04 0.0125 + jo.03 2.
AC Power and Power Factor 1. Two loads are connected in parallel across a 13,200-volt line. Load A draws 200kW at 0.6 p.f. (lagging), load B takes 200kVA at 0.8 p.f. (lagging). Find the reactive, apparent and true power and the line current.
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
4) A balanced delta connected load of ...+j18 ohm per phase is connected at the end of a three phase line as shown in figure. The line impedance is 1+j2 ohm per phase. The line is supplied from a three-phase source with a lie- to-line voltage of 207.85 V rms. Taking Van as reference, determine the following: a) Current in phase a. b) Total complex power supplied from the source. c) Magnitude of the line-to-line voltage at the load terminal. (Please determine the impedance value within the specified limits: 16-26 V. By considering the impedance value you determined yourself, solve the question.) ao- |V₂| bo Co- 1 +j2 Ω = 207.85 V www Figure a Jum ...+j18 n b
1. a) Find the average power dissipated in the line shown.2. b) Find the capacitive reactance that when connected in parallelwith the load will make the load look purely resistive.3. c) What is the equivalent impedance of the load in (b)?4. d) Find the average power dissipated in the line when the capacitivereactance is connected across the load.5. e) Express the power loss in (d) as a percentage of the power lossfound in (a).
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Zload = 500 236.87° ohm, and the transmission line's impedance is Zline = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. ' qu V = 1.05200 0.01+ j0.025 300 + j200 MVA 3 0.015 + j0.035 150 MW 200 + j150 MVA 0.01 + j0.03 |V = 1.03 The admittance matrix (Y_bus)? The bus power in per-unit?
Consider the circuit shown. Find the following: a. Total load impedance seen by the voltage source. b. Complex power delivered by the source. c. Average power delivered by the source. d. Reactive power delivered by the source. e. Load power factor and power factor angle.
Problem 4- A large 3-phase industrial load draws 3.6 MVA at 0.85 power factor lagging from through a three- phase 12.47/7.2 kV 3-wire overhead distribution line. The phase conductor is #1 ACSR “Robin". Taking 3.6 MVA and 12.47 kV as base values, determine (a) The base impedance in (N) (b) The reactive power drawn by the load (p.u.) (c) The total current (p.u.) drawn from the power supply
2. Two transformes A and B of ratings 5uokVA and 25okVA. Supplying a load kVA of 750 ato.8Pf lagging. open circunt valtajes are 400V and 410v respectively. Trusfarmn A has 1/ nsistance and 5/ ractance and traugformer B hay 1.$, mesistona and 41 reactance. Find (^) Crossacarent in the seandaries on no.load.ib) the load shared by euch transfarmer Their are
There is an installation with two equal triphasic loads of 300 kVA each and a power factor of 0.9 lagging. When connecting a pure reactive element in parallel, the reactive power at the entrance of the installation is 150 kVARS, with a lagging power factor. We can say that: a) A bank of reactors was connected and the fp deteriorated. b) A capacitor bank was connected and the pf deteriorated. c) A bank of reactors was connected and the fp improved. d) A capacitor bank was connected and the pf improved. e) None of the above
Two balanced loads are connected to the a 240kVrms60Hz line as shown in the figure below. Load 1 draws30kW at a power factor of 0.6 lagging and load 2 draws 45 kVAR at power factor of 0.8 lagging. The real power, reactive power, and magnitude of the line current absorbed by the combined load is close to kW, kVAR, and A. Two balanced loads are connected to the a 240kVrms 60Hz line as shown in the figure below. Load 1 draws 30kW at a power factor of 0.6 lagging kW. and load 2 draws 45KVAR at power factor of 0.8 lagging. The real power absorbed by the combined load is close to Balanced load 1 Balanced load 2