Q, Beginning in position lin Fig. 4.32, the switch is thrown into position 2 andheld there for 10 ms, then back to position 1 for 10 ms, and so forth. Sketch theI resulting output waveform if its initial value is 0 V. The saturated output levels ofthe op-amp are ±12 V.+5 V10 uF20R10 kN-5 VFig. 4.32.Qe A triangular waveform is applied to the input of the ciréuit in Fig. 4.33 asshown. Determine what the output should be and sketch its waveform in relation tothe input.R10 kNVi 010 us0.001 µF

As per our guidelines we are supposed to be answer the first question only. Kindly repost the other…

Q, Beginning in position lin Fig. 4.32, the switch is thrown into position 2 and held there for 10 ms, then back to position 1 for 10 ms, and so forth. Sketch the resulting output waveform if its initial value is 0 V. The saturated output levels of the op-amp are ±12 V. C +5 V 20 R 10 uF 10 k2 -5 V Fig. 4.32.

Q, Beginning in position lin Fig. 4.32, the switch is thrown into position 2 and held there for 10 ms, then back to position 1 for 10 ms, and so forth. Sketch the resulting output waveform if its initial value is 0 V. The saturated output levels of the op-amp are ±12 V. C +5 V 20 R 10 uF 10 k2 -5 V Fig. 4.32.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Figure Q4(b) shows an amplifier block diagram. Design using MORE THAN ONE op-amps which have one common input signal and two output signals. Shows all necessary calculation of the design. Vil: - 200mV Figure Q4(b) • Vo2 = 20mV Vo3 = - 1V
Figure 6 (a) shows the circuit diagram for a differential amphfier. You may assume that M and M, have identical parameters. Referring to Figure 6 (a): (a) What kind of amplifier is it? What is its role in a three-stage op amp? Draw the small signal equivalent eircuit and derive the differential voltage gain Aag. For the analysis consider RDI RD2 >>Rp State any assumption. (b) RD. gml gm gm, and r re=r What is the new Adr in the circuit of Figure 6 (b), where a PMOS current source has replaced the two drain resistors Ror R Rp and a NMOS current sink has replaced the source resistor Rs? (c) What are the advantages in using the circuit of Figure 6 (b) instead of Figure 6 (a) to realize an op amp? (d) Ven Ms Mg Rp1 Rpa Vo HM, My M Ma M3 Vss 0 V Vss 0 V Figure 6(b) Figure 6 (a)
Sketch the output voltage against time diagram for the values given in Q4 in the following cases: a) Vin is a sine wave with peak-to-peak voltage of 8 V and period of 5 ms. b) Vin is a sine wave with peak-to-peak voltage of 4 V and period of 5 ms. +Vs Vin A Vout V. -Vs R2 + R1 Vref Figure 2
10 V(p-p),1KHz sinusoidal voltage is applied to op-amp input and non-inverting input isgrounded. What is the gain of this op-amp and why?
Consider the following circuit using diode and Op-Amp. Assume ideal Op-Amp with output saturation at +-13V. Assume diode forward drop is 0.7V. a. Find Vo and VA when Vin = 1V and 3V. b. Find V, and VA when Vin = -1V and -3V. R Vin R VA ovo ER₂
The two input terminals of an op-amp are connected to voltage signals of strength 745µV and 740µV repectively. The gain of the op-amp in common mode is 50 and CMMR is 8&IB. Calculate the output voltage and % of error due to common mode.
4. a) Define the function of opamp circuit given below. b) If the voltage gain is 50 for the circuit shown below, find the Rf value. b-Vcc R R = 5K
Example 07:- For the circuit shown in the figure, calculate the output voltage when 1- R1 = R2 = R3 = R4 = 1002 2- R1 = R2 = R3 = 100N and R4 = 1202 Consider the circuit use an ideal Op-Amp and its resistances do not load the bridge circuit. 12K 10K E 10V 10K 12K ww
The two input terminals of an op-amp are connected to voltage signals of strength 754µV and 740µV repectively. The gain of the op-amp in differential mode is 50 and CMMR is 80 dB. Calculate the output voltage and % of error due to common mode.
Example 07: For the circuit shown in the figure, calculate the output voltage when 1- R1 = R2 R3 = R4 = 100n 2- R1 = R2 = R3 = 1002 and R4 = 1202 Consider the circuit use an ideal Op-Amp and its resistances do not load the bridge circuit. 12K ww 10K 10K 12K 10V
Q4/A)- Show the connection of three combination op-amp stages using an LM348 IC to provide outputs that are 110, 1681, and 420 times larger than the input. Use a feedback resistor of Rf = 400 k? in all stages, while can use only (R= 40 k? for first stage), (R= 10 k? for second stage), and (R= 20 k? for third stage
1) Op-amp limiting factors - Current Saturation U2 Vin R1 OUT OPAMP R2 RLoad The saturation output current for the above op-amp is +/- 15mA. For the following input signals, determine if the output appears as would be expected in an ideal circuit. Include sketches of the output voltage. a) R1 = 100, R2 = 900, an open circuit load, and Vin is 2Vpp triangle wave with zero offset voltage (Vmax 1V, Vmin = -1V) and a period of 2ms. b) R1 = 100, R2 = 900, a 1k load, and Vin is 2Vpp triangle wave with a 1V offset voltage (Vmax=2V, Vmin = 0V) and a period of 2ms. c) R1 = 100, R2 = 900, an open circuit load, and Vin is 4Vpp triangle wave with zero offset voltage (Vmax=2V, Vmin = -2V) and a period of 2ms.