Q-2: For a simply supported beam shown in figure below and by using Ultimate Strength Design Method, find the area of steel for the following data:- W 20KN/m, WD-18KN/m (including self-weight), f-400MPA, f-30MPa, b-250mm, d-400mm, dt-422mm, if there is need for compression steel use d'-50mm. Wp 18KN/m WLA20KN/m Brick Wall 8m

Q-2: For a simply supported beam shown in figure below and by using Ultimate Strength Design Method, find the area of steel for the following data:- W 20KN/m, WD-18KN/m (including self-weight), f-400MPA, f-30MPa, b-250mm, d-400mm, dt-422mm, if there is need for compression steel use d'-50mm. Wp 18KN/m WLA20KN/m Brick Wall 8m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What will be the tensile strength due to rupture of critical section of an angle section ISA 150 × 115 x 8, which is connected to gusset plate as shown in figure?. Use Fe410 grade steel. 150 mm 115 mm 8 mm 8 mm 60 mm 150 mm
Plastic stage is when all elements of a steel section is in yielding condition and reaches its utlimate strength before it collapses without lateral torsional buckling. O True O False
i need the answer quickly
Calcualte the following: Total factored floor load in 2 decimal places, ___ kPa Total factored uniform load on girder GH in 2 decimal places, ___ kN/m Maximum ultimate bending moment at discontinuous end of girder JK to the nearest whole number = ___ kN·m
B7
Z1
plss, i need the answer immediately!
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P= 20 KN is applied. Sleel E-200 GPa A-400mm L1 m 2.0 m 0.6 m 1.5m P-20 KN Aluminum E70 GPa A-900mm L-1.5 m 1. Axial load at steel rod in kN? 2. Axial stress at steel rod in MPa? 3. Axial deformation of aluminum rod in mm? 4. Axial deformation of steel rod in mm? 5. Axial Load at aluminum rod in kN?
How to solve this question step by step
A For the truss shown, find veyticat deflection bylunit lead Methed. EA 15 _atfd) Ioku for all members increase in temp is (50€) in (ad) short in (ad)is (3 Emfr
5 5a 5b 5c Alaterally supported beam was designed for flexure. The beam is safe for shear & deflection. The most economical section is W 8 x 13 however the said section is not readily available at the time of the construction. If you are the engineer in charge of the construction what alternative section will be the best replacement? Why? Use: Fy=248 MPa: E=200,000 MPa Designation Ag (mm2) Weight kg/m 1910 19 30 width 24 flange. thickness d (depth) mm 200.41 bf 100.06 W8 x 10 4.32 15 expla'n briefly your cho'ce. (transform your comparative analys's 'nto a narat've form to support your cho'ce) W8 x 13 2477 202.05 101.60 6.48 W6 x 20 3787 157.48 9.27 152.91 102.36 W6 x 16 3058 159.51 10.29 tf Web 5.21 thickness tw Elastic Properties mm 4 Ix x 106 mm 3 Sx x 103 5.84 6.60 6.60 13 16 17 13 126 162 220 167 mm rx 81.79 81.53 67.56 66.04 mm 4 lyx 106 1 1 6 2 mm 3 Sy x 106 17 22 72 36 mm ry 21.36 21.41 38.10244 24.54 Plastic properties mm 3 Zx x 103 145 187 244 192 mm 3 Zyx 103 27 35 110 56…