The beam under the Live and Dead loads is shown below. The steel class is $235. 4.8 A L1 L2 a.) Evaluate the slenderness of the web and flange. b.) Calculate the Cb value based on the loads. c.) Calculate the bending moment capacity of the beam... d.) Is the beam cross-section enough for the given loads. L3

The beam under the Live and Dead loads is shown below. The steel class is $235. 4.8 A L1 L2 a.) Evaluate the slenderness of the web and flange. b.) Calculate the Cb value based on the loads. c.) Calculate the bending moment capacity of the beam... d.) Is the beam cross-section enough for the given loads. L3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam subjected to a uniform service Dead load of 20kn/m (including the weight of the beam), a uniform service live load of 35kn/m. The beam is 12m long and is laterally supported at midspan, and A572 Gr. 50 steel is used. Assuming cb =1. Verify if w30x108 is adequate? Use fy=344 mpa
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES - STEEL DESIGN Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee
In steel design use nscp 2015 i need a complete solutions ty..
Rigid member BED is supported using steel rods AB, CD, and EF as shown below. E-200 GPa for steel. If a force P is applied at E, determine: a) The stress in each rod b) The length of each rod after applying the force LI (mm) LI (mm) P (kN) AAB (mm2) ACD (mm?) AEF (mm) 395 350 20 250 250 450 L1 L2 Note: BE ED P.
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES - STEEL DESIGN
i need the answer quickly
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis
2
I need the answer as soon as possible
A rectangular tied braced column is reinforced with 6-28mm bars as shown in the figure below. Check the adequacy of the column for the following gravity loads: - - - - - - Service dead load = 1050kN Service live load = 850 kN Service dead load moment = 39 kN-m Service live load moment = 27 kN-m top=bott. = 1.0 40 lu = 5.0m f = 27.6 N/mm², fy = 414 N/mm² axis of bending 500mm Ties 10mm@300c/c } 350mm At eccentricity of 40mm P M +40 + 500mm MU +40- P Top end Bott. end
SOLVE please Determine the design bending strength of ISLB 350 @ 486 N/m, considering the beam to be laterally supported. Assume factored design shear force will not exceed 0.6 times the design shear strength of the cross-section. If it is used as simply support beam of unsupported length 5 m then determine the factored distributed load the beam can carry. Use Fe410 grade steel For ISLB 350 @ 486 N/m, section properties are as follows: h = 350 mm; b= 165 mm; t₁ = 11.4 mm; t = 7.4 mm; R₁ = 16 mm; Izz = 13158.3 × 104 mm²; I = 631.9 × 10¹ mm²; Zpz = 851.11 × 10³ mm³; Zez = 751.9 x 10³ mm³
Given the truss shown, solve the following. Use A36 steel and assume there are two lines of three 19 mm bolts in each flange. Hole diameter is assumed to be three mm more than the bolt diameter. Neglect the weight of the section. a.What is the capacity of member CG? b. Design member CG using a W section. c. What is the tensile capacity of the section for CG based on gross area? The following W Section were considered for the design: W10x33 W14x38 W8x40 W16x36 W10x39 W8x13 189 KN 1.50 HL B 145 KN 1.50 E + 137 KN 121 KN -3.00 + 12.00 3.00 154 KN + W4x13 W6x9 W10x12 200 KN -1.50 1.50 1 030 T 1.20 +2.40 0.60 L i 0.30