Q # 1: Design main reinforcement and shear reinforcement for beam carrying total design load including self-weight 70 kN/m, considering rectangular cross section having width (b) 200 mm, and total height of beam (h) 300 mm, concrete cover 40 mm, concrete grade 30, fy = 460 N/mm?. Assume: Diameter of tension bar 25 mm Diameter of compression bar 16 mm, if required Diameter of shear link 10 mm 70 kN/m 3 m

Q # 1: Design main reinforcement and shear reinforcement for beam carrying total design load including self-weight 70 kN/m, considering rectangular cross section having width (b) 200 mm, and total height of beam (h) 300 mm, concrete cover 40 mm, concrete grade 30, fy = 460 N/mm?. Assume: Diameter of tension bar 25 mm Diameter of compression bar 16 mm, if required Diameter of shear link 10 mm 70 kN/m 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design main reinforcement and shear reinforcement for beam carrying total design load including self-weight 70 kN/m, considering rectangular cross section having width (b) 200 mm, and total height of beam (h) 300 mm, concrete cover 40 mm, concrete grade 30, fy = 460 N/mm2.Assume: Diameter of tension bar 25 mm Diameter of compression bar 16 mm, if required Diameter of shear link 10 mm
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As
Q2// A floor system consists ofconcrete slab supported by continuous beam h = 140mm , bw = 300mm,d = 550mm, f 28MPA, fy = with: %3D 420MPа. Determine the steel reinforcement required at mid span of interior beam to resist service dead load moment Ma = 320KN.m and service live load moment M = 250 kN.m %3! %3D 8m + 3m 4 3m 3m 1-1
1. A simply supported reinforced concrete beam of dimension 230 mm width is subjected to a service point load and UDL as shown in Fig.1. Analyse the beam for flexure at point B and shear at support A and C ). Use M20 grade concrete and Fe415 grade steel. Assume cover to main reinforcement is 40 mm from mid of reinforcement to extreme fibre of tension zone. Sketch the reinforcement details clearly. 1000 kg 200 kg/m. A 3m 3m R R
A RC beam of cross section 220 × 460 mm is subjected to following forces: Factored shear force = 30 kN Factored bending moment = 35 kNm Factored torsional moment = 5 kNm What should be the minimum area of tension steel provided such that there is no need to provide torsional reinforcement. Use M20 grade concrete and Fe415 grade steel. Use the following data for M20 grade concrete. 100 As 0.50 0.75 1.00 1.25 1.50 bd Design shear stress (N/mm²) 0.48 0.56 0.62 0.67 0.72
Q₁:Design a concrete column shown in figure using fe-28 MPa, fy- 420 MPa, ultimate applied load. P=545 KN B E 1500 P=350 KN b Section (a-a)
Question 2: Determine the required reinforcement for L section beam to resist torsion T = 10KN.m with the following dimensions; depth of slab = 100 mm, width of flange = = = 200 mm, 900 mm, width of web depth = 455 mm. Consider concrete class C30 and high yield steel S460 for main Reinforcement and S250 For stirrups. 900mm = 1120 mm² -200mm
2012 300 mm D 3014 250 mm Check the requirements of TS500 for ductile design and Determine the Moment resisting capacity, Mr, of doubly reinforced section. Material: C30/B420C Concrete cover=25 mm
Determine the numbers of rebars required for a RC beam (h=400mm, b=700mm) carrying a factored moment of 734 kNm. The concrete used has a compressive strength of 28MPa, while steel yields at 345MPa. Assume single layer of reinforcements (compression and/or tension side) and do not check for rebar spacing anymore. Other parameters: Cc = 40mm db = 20mm ds = 10mm
Situation: A beam has a width of 300 mm and total depth of 600 mm strength f'c-36 MPa. Steel yield strength fy=415 MPa The section is to be reinforced for tension only and the effective concrete cover is 65 mm. Which of the following most nearly gives the value of our balanced steel ratio? a. 0.00370 b. 0.03456 C. 0.02860 d. 0.03522 Which of the following most nearly gives the value of our balanced distance of the cuter most fiber of compression fiber to our neutral axis? a. 313.256 mm b. 354.68 mm C. 333.333 mm d. 322.435 mm Which of the following most nearly gives the value of our balanced depth of compression block? a. 248.412 mm b. 266.2676 mm C. 301.478 mm d. 281.261 mm
A reinforced concrete T – beam is to be designed for tension reinforcement only. The beam width is 250 mm and the effective depth is 400 mm. The flange thickness is 100 mm and its effective flange width is 900 mm. The applied moment is 300 kN–m. What is the area of tension reinforcement required? use: fc’ = 20.7 MPa and Fy = 414 MPa. * a. 3 983 mm² b. 5 105 mm² c. 2 166 mm² d. 4 094 mm²
4) A simply supported beam is reinforced with 4-ϕ28 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = __________ mm Design strength of the beam section to the nearest whole number = ___________ kN·m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = __________ kN/m (to the nearest whole number)