pump is to deliver water from an underground tank against a static head of 40m. The suction pipe 50m long and is of 25 cm diameter with Darcy-weisbach friction factor, f = 0.02. The delivery pipe of 20 cm diameter, 16m long and has f = 0.022. The pump characteristics can be expressed as: = 100-6000Q2 Where, H = Pump head in meters. P Q = Discharge in m³/sec. Calculate the head and discharge of the pump.

pump is to deliver water from an underground tank against a static head of 40m. The suction pipe 50m long and is of 25 cm diameter with Darcy-weisbach friction factor, f = 0.02. The delivery pipe of 20 cm diameter, 16m long and has f = 0.022. The pump characteristics can be expressed as: = 100-6000Q2 Where, H = Pump head in meters. P Q = Discharge in m³/sec. Calculate the head and discharge of the pump.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

simple solution is needed
14. Water is pumped from one tank to another through a 0.100 m smooth plastic tube. The flow rate is 0.200 m³/s. The head loss due to major and minor friction losses is given by the equation, h₁ = 12.0 2g V 25 m Pump Determine the pump head. Also determine the shaft work done by the pump.
Draw hp, hes and h, for the system shown in figure (A). Flow V Soil T K=1.5 cm/sec 2 Soil Il K=0.5 cm/sec Figure (A) DIL 1.0 m 1.5 m 1.0 m 1.0 m 1
Read the question carefully and give me right solution according to the question
Water flow at a 250mm diameter horizontal pipe 875m long. The friction factor is 0.023. If the pressure at the starting point is 80KPA and the pressure at the end point is 50KPA. Determine the discharge at the pipe. A Q = 153.68 L/s В No answer among the choices C) Q = 101.07 L/s D) Q = 118.43 L/s E Q = 132.74 L/s F Q = 172.81 L/s %3D
Water flow at a 250mm diameter horizontal pipe 90m long. The friction factor is 0.023. If the pressure at the starting point is 80KPA and the pressure at the end point is 50KPA. Determine the discharge at the pipe. A Q = 118.43 L/s В Q = 132.74 L/s Q = 101.07 L/s D Q = 172.81 L/s Q = 153.68 L/s No answer among the choices
3) A centrifugal pump delivers water between two reservoirs with a 300 ft. elevation difference (Az). The 12-in diameter suction pipe (f1= 0.020) is 100 ft. long (L1) and the 10-in diameter discharge pipe (f2= 0.026) is 5000 ft. long (L2). The pump has a performance curve defined by the equation: h, = 375 - Q² where h, is the pump head in feet and Q is the discharge in ft/s. a) Calculate the discharge, Q. b) Calculate the NPSHA. Assume standard atmospheric conditions, 60°F water, and a pump elevation 8 ft. above the lower reservoir Az D, L2 2 D, Ly. ft LOM
Consider the figure shown below. If the flow rate of water from the tank is 0.03 m/s, the pressure at point 2 is 120kPa. Height of water in the tank is 4m and the pipe diameter is 160mm with a friction factor of 0.020. Solve for the height h if the branch line is shut off, and if the branch line is open so that half of the flow from the tank goes into the branch and half continues in the main line. Determine the difference in the head losses in both directions. Neglect minor losses. Vent | 4m 160mmø pipe Branch Line B A 1.75m Main Line 300m 200m ANSWER: a. h = 13.918m, b. h = 10.585m c. HL = 3.2479m
شمذنس Fluid mechanics
Please correct answer And solve both part
Q.solve itt.