Please give correct, neat and clean handwritten solution for an upvote. Thanks in advance Question 13Pump efficiency = 86%Pump Speed = 2,342 rpmPump discharge = 428 L/s of water to a height of 78 m.Determine the power output of the pump in kW.

Givenη=86%N=2342rpmQ=428 L/s=0.428 m3/sH=78m

Answered: Pump efficiency = 86% Pump Speed =…

Pump efficiency = 86% Pump Speed = 2,342 rpm Pump discharge = 428 L/s of water to a height of 78 m. Determine the power output of the pump in kW.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: It is a widely use tool for laying out squaring and checking work.It consists is a square head and a…

A: following is the answer to the above question-

Q: The efficiency of a power screw does nột depend on which of the following variables. Hint: Look at…

A: formula for efficiency of power screw is given byη=Fl2πThere F=load in newtonl=lead T=torquetorque…

Q: Write the sequential procedure for making the simple step turning operation for making the shown job…

A: The sequence for making the simple step turning operation for making the shown job: 1. Centering 2.…

Q: Calculate the time to complete one circular motion. How to double the time?

A: Given data:Helicopter mass = 400 kgcircular motion radius, r = 20 mRotor blade resonant frequency =…

Q: How is spindle aligmment done in a milling machine?

A: By spinning a cutting tool (cutter) and sliding it into the work item, a milling machine removes…

Q: Write a note on different types of gear along with application.

A: The gears are used for power or torque transmission. They are generally used whenever the positive…

Q: 1. The . . tool is used to draw the cutting plane line arrowheads in AutoCAD .... a. spline fit b.…

A: 1) d) polyline 2) c) revolved 3) b) partial 4) b) half

Q: MI Match column A with Column B (Return this page with your answer shcet) No 1 Column A No A Column…

A: given; match with column A to column B.

Q: Read the sentences given below and Identify the wrong statement. Sentence 1. The advantage of an…

A: Independent chuck is a four jaw chuck that is used to hold the workpieces. In this chuck each jaw…

Q: Which therbligs correspond to which activities? 1.Lift and move wrench toward screw 2.Reposition…

A: Solution:

Q: 3. (a) In the set-up shown, if the support columns are removed, what will happen to the see-saw?…

Q: 9. To produce the line of intersection between the two cylinders, connect the project points using a…

A: Since we only solve up to three subparts, we will answer the first three. Please resubmit the…

Q: I need the complete procedure, that is, where did you find the value of 895

A: How the value 895 came in the formula

Q: Ql:- Put a mark of True or false for below:- (a):- The milling cutting tool has a single cutting…

A: As per bartleby guidelines we are allowed to solve only 1st 3 subparts if multiple subparts are…

Q: short notes on any two types of chips formed during metal cutting operation

A: Metal cutting is defined as "the act of eliminating undesirable material from a block of metal in…

Q: In the following milling method, metal is cut by a cutter rotating in the same feed direction of…

A: Ans- b. Down milling.

Q: a) The maximum force P that can be applied to the system based solely on the boards is most nearly…

Q: Match each of the following terms to the phrase that describes it. Answers are used only once.

A: The correct match is: Drill spot - 3Countersink - 6Knurl -…

Q: 9. Please list the basic procedure of calculating the X- and Y-coordinates of the tool centerline…

Q: Write the sequential procedure and CNC code for making the simple step turning operation for naking…

A: CNC Codes: There are two types of codes used in CNC programming G Codes M Codes

Q: List down the formulas for calculating the shear stress and angle of twist of the following cross…

A: It is asked to write the shear stress and angle of twist formula for the cross-sections of shape…

Q: Find the spindle speed in rpm, if the slotting operation is performed by 14mm end mill with a…

A: Given data Mill diameter (d) = 14 mm = 14 x 10-3 m Cutting speed (v) = 16 m/min

Q: 1. List the operations and the tools needed to make the following shape. 2. Find the speed of…

A: 1. operations and the tools needed to make the following shape are listed below:

Q: On the attached drawing, is the allowance between "shaft C" and "hole D" positive or negative?

A: Allowance is the difference between the basic dimensions of the mating parts. There are two types of…

Q: Write the sequential procedure for making the simple step turning operation for making t shown job –…

A: To obtained required finished product we have to perform sequence of operations on lathe machine.…

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given - L = 25 ft = 25 × 12 P = 10000 lb ∆L = 0.477 in E = 30 × 106 psi

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following.…

A: In machining, taper turning is a process in which the diameter of cylindrical workpieces reduces…

Q: Shaper machine uses single point cutting tool for cutting mater Select one: True False

A: 1.true

Q: In a tap set, a plug tap is used for final cutting the thread throughout its length after using two…

A: Solution:

Q: a) Name and explain any six lathe operations with neat sketch.

A: The Common lathe operations are turning, facing, grooving, parting, threading, drilling, boring,…

Q: For the following thread designation, turns, how far have you advanced the O 083 inches O 417 inches…

Q: I have three parts that I need answered pertaining to the print provided below. Based on the shape…

A: Section B - An offset view.

Q: QUESTION 1 Calculate the spindle speed in RPM of a lathe turning a 96 milimeter diameter material…

A: Given:d=96 mmV=148 SMPM

Q: Q1/B) Match between Column A & B. A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical…

A: To match: The column A and B. Given: Cutting fluid also known as emulsified oil. 1. Cutting fluid…

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following. )…

A: The most common lathe machining operation is turning. A cutting tool removes material from the…

Q: Identify the side relief angle (in degrees) from the following single point tool signature 1-…

Q: Determine the spindle speed (rpm), the feed rate (in/min) and the cutting power required for turning…

A: As two questions are independent so I am answering Q.5 as per bartleby policy. Please post Q.6…

Q: Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has…

Q: is the lathe operation, which is performed without the cutting tool moving parallel to the axis of…

A: Lathe is a machine tool which is used in the work shop to perform the various machining operations…

Q: High tensile strength materials are cut by a single point cutting too with the negative rake angle.…

A: Negative take is angle is used

Q: The robot shown below has one prismatic and one rotary link. Draw the work space if the prismatic…

A: To solve the problem, we need to draw the workspace of the robot described. Here are the steps to…

Q: A mild steel specimen of Initial diameter of 51.5 mm is turned to final diameter of 45 mm for an…

A: Turning is a machining process used to decrease the diameter of a workpiece. Turning is done using a…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

Please give correct, neat and clean handwritten solution for an upvote. Thanks in advance

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Need questions 13, 14, 15 explained and answered please.
PLEASE ANSWER THIS USING YOUR OWN ANSWERS. DO NOT COPY ON INTERNET. IF YOU SEE THIS QUESTION AGAIN, DO NOT ANSWER. IF YOU ANSWER THIS IN TYPEWRITTEN, COMPLETE, CORRECT, AND IN ORIGINAL WAY, I WILL UPVOTE. THANK YOU!
I need help matching each drawing to the term that it describes. Answers are used only once.
What’s the correct answer for this please?
Can I get the Top, Side and views. Using free-hand drawing of this coupling pieces..
What’s the correct answer for this please?
Required information Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has a 1.250-inch-thick bar that needs 90° grooves machined into it for precision ground 1.0000-inch diameter cylinders. A sine bar is used by placing different thicknesses under one of the cylinders so that the proper angle is attained. Sally wants the distance between the centers of the cylinders to be D= 5.9 inches. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 7 -1.00000 * How deep should she mill the 90° grooves so that the top of the sine block is 2 inches tall? (Round the final answer to four decimal places.) The depth of the mill should be 7071.067 inches.
Hello, please answer as soon as possible. Choose from the given choices/options below the question. Show complete solution. Thank you for your help. I’ll rate you with like/upvote.
TYPEWRITTEN ONLY PLEASE FOR UPVOTE. DOWNVOTE FOR HANDWRITTEN. DO NOT ANSWER IF YOU ALREADY ANSWERED THIS. I'LL DOWNVOTE.
Give at least 7 machine/equipment and their uses. PLEASE TYPE THE ANSWER
need handwritten answers