Propertics HP 410 x 13) 399mm 13.17mm A - 16, 600 mm Cx : 167 mm %3D fy: 93. 5mm fy: 345 mpg T13.7mm

Q: 1. Given the following set of stadia level notes. The instrument used has a stadia interval factor…

A: Given, STA   BACKSIGHT     FORSIGHT         INTERCPETS VERTICAL ANGLES () ROD RDG (RR1)…

Q: 6M WL 6

A:

Q: Remotely sensed images from the Landsat mission have been purchased for your outfit. How will you…

A: Remotely sensed images are high-quality images taken from the satellite. These pictures are used in…

Q: Req. at point A&B in the network

A:

Q: In supervised classification, we select training data to guide the software to: Select one: O a.…

A: Supervised Classification: In supervised classification the user or image analyst “supervises” the…

Q: A subtense bar is a tripodmounted bar with targets set precisely 2 meters apart. This technique is…

A:

Q: PROBLEM : For the beam shown below, do the following: 1. Find the reactions; 2. Find the shear and…

A: "since you have posted a question with the multiple  subparts , we will solve first three for you as…

Q: TEST II: DRAW THE ISOMETRIC VIEW 20 Mm 20 20 TOP VIEW 5. FRONT VIEW SIDE VIEW 20

A:

Q: Which Data Collector sequence of screens brings you to the Offsets options menu? SeheBacksightSet…

A: Note - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: Please explain why we say (2n -1)As'

A: Solution: The long term stresses in the compression reinforcing steel will be affected by the creep…

Q: In . mode, cursor movement is constrained to the horizontal or ..... vertical direction relative to…

A: Finding out the correct option of given statement.

Q: In fig. FV on the curved gate is ---? If the gate width is 3 m

A: solution the force acting on the curved plate is given as F=γ×volume of water acting…

Q: Draw an approximate (i) front view (ii) top view and (iii) view from left of the object shown in…

A: i)The front view :

Q: Find headlight sight distance and intermediate sight distance for V=70kmph. (Hint: f=0.36,t-2.5 s,…

A:

Q: Compute the azimuthof the missing side. (Format: 000deg00min) 00- numerical values LINES AZIMUTH…

A:

Q: For erasing files in MS DOS we use *.the... ..command

A: MS DOS is a computer program which is use for computer work.

Q: IV - Coordinate measurement Oa) 1, II, II, IV OB) I, II, IV OC) I and III OD) I and II O TO) II and…

A: Brief concept- The image shown is of auto-level. This is used commonly in surveying for leveling…

Q: a-What is the height of instrument between TP-1 and TP-2? b-What is the unadjusted elevation of…

A: Differential levelling: The process of measurement of vertical distances from the known elevation…

Q: 62.5mm 600mm 62.5mm 350mm Pn

A: Compression member is a structural member which is primarily subjected to axial compression. If…

Q: ISK 30k 9.

A: the above beam is determinate beam and its can be analyze by the given equilibrium equation.…

Q: The following are ordinates of 5hr UH. Derive and plot FH due to excess RF of 60mm

A: Since the ordinates of 5hr UH is not mentioned assuming it to be m3/s Rainfall excess (n) = 60 mm…

Q: WRITE AN OBJECTIVE, INTRODUCTION AND CONCLUSION (ATTACHED PHOTO ARE THE DATA AND RESULTS). ITS ABOUT…

A: This is profile leveling . It is used to determine elevations of point with respect to bench mark.…

Q: lat Jength vertical phoograph: The terrrain A section Jine of g00 m on a focal measures 100 on used…

A: Given data, f = Focal length = 20 cmx = Length of line in photograph = 100 mmX = Length of line on…

Q: 14- Image enhancement deals with? A. The image histogram B. The spectral signature C. The number of…

A: Question being asked here is Image enhancement deals with?   ANSWER IS OPTION-D- ALL OF THE ABOVE

Q: Which of these is NOT a required device/information for the horizontal angle measurement? a)…

A: This given question is from surveying Here we are asked to find instrument/ information required for…

Q: Describe about the piezocone penetrometer?

A: - The Piezocone penetrometer is a type of Cone penetration test apparatus which is field method used…

Q: 2 L 13mm 5mm mm 3mm Select one: a. 9.95 b. 10.11 c. 7.52 d. 8.73 6mm

A:

Q: Obberved beaning computer Correstien Adjusted values Internal Porward BacK angle Beaning Begring…

A:

Q: Cover pen, shapes and stamps are available PDF Annotation 2. Locate the centroid Y of the beam's…

A: Note : Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: In .... mode, cursor movement is constrained to the horizontal or vertical direction relative to the…

A: e)Ortho In Ortho mode, cursor movement is constrained to the horizontal or vertical direction…

Q: With the visual device located in the following operationsn Which / Which can be done? I- Angle…

A:

Q: - Read: CS Scanned with CamScanner 25m Maximum Minimum WM 5m 8 kN/m Tension Tension

A: Given data in question  Span 25 m Dip 5 m Load 8kN/m To find out  Maximum tension Minimum tension

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land.  Zoning is done or can be understood with the help of a site plan.