Compute the azimuthof the missing side. (Format: 000deg00min) 00- numerical values LINES AZIMUTH DISTANCES A-B 225°00' 1200 m В -с 346°00 1400 m C-A ----

Q: 3. From the given data of a compass survey, compute the corrected bearing of line DE. LINE FORWARD…

A: Given: Line Forward Bearing Backward Bearing A-B N 30° 30' W S 32° 15' E B-C S 80° 45' W N…

Q: The moment of inertia (second moment of area) about a horizontal centroidal axis is closest to:…

A:

Q: R-M Q1: Compute:- a) vertical distance AB. b) ABC area. M=R-cosR staff in A staff in B 6ố số AB…

A:

Q: A drawbridge is being raised by a cable El. The four joint loadings shown result from the weight of…

A:

Q: A circle has its center at ( 3, 4 ) and tangent to the y - axis. A line has its point of tangency to…

A: ASKED: To compute the value of y, corresponding to the y-coordinate of a point of tangency to the…

Q: 1 15m 1.05 2 25m 1.20 3 30 M 1.32

A: Station A  Stadia rod 1   =  D = Ks1 + c                                15 = 1.05 K + c Stadia rod 2…

Q: Determine the centeroid of the shaded area * ?shown in fig y 8 R= 1.5 5 4 个

A:

Q: Bearing or Azimuth of Line AB: Adjusted Interior Sta Sta Dist Мean Observed Interior Angle 0 Corr…

A: A bearing is a clockwise or counterclockwise angle between north or south and a direction. The…

Q: Find Find 300 EN 30 F1= 205KN

A:

Q: Determine the moments of inertia of the cross-sectional area as shown about the centroidal xo-yo-…

A: A cross section is given we need to find out the moment of Inertia

Q: ду 5WL3 384EI (5×4369.43722kg x 33m3) 384 х 200GPах 188 × 106 mm

A:

Q: Q.02. The floor beam in below figure is used to support 6 meters width of a plain concrete slab…

A: GIVEN DATA: DENSITY OF PLAIN CONCRETE=22KN/m3 DENSITY OF ROCK=26KN/m3 DENSITY OF PLASTER =18KN/m3…

Q: By integration determine the centroid of the shaded area shown Ty-axis 50 mm 30mm X-axis

A: The centroid of an area normally is the geometric center of that area.  Divide the total area into…

Q: Truss 2KN and 60 degrees

A:

Q: 9KN

A:

Q: 94.40mm 16.50mm 348.00mm 36.40mm 16.50mm

A:

Q: Determine the radius of gyration through the centroid (x and y), 175 mm 35 mm YG N.A. dz 180 mm 35…

A: Given :

Q: Observed Bearings Length (m) Computed Internal Adjusted Values Line Forward Вack Sta Cor Interior…

A:

Q: Solve for the bearing of course FA. (answer format: in two decimal places and indicate direction,…

A: Calculation of Bearing of FA###

Q: find CJ. method of sections

A: Given data - P = 780 N Find out - Force in member CJ ?

Q: STATION DIRECT DOUBLE MEAN REMARKS DEFL. DEFL. DEFL. Azimuth 111 - 112 = 121° 21' 111 147° 01' 293°…

A: Station Direct Double Mean Remark 111 147°1' 293°59' 147° (147°1'+293°59')/3 112 116°11' 232°22'…

Q: 18. The term vertical line in levelling is a line parallel to the direction of gravity. a. True b.…

A:

Q: Lines Bearing Distances(m) АВ N 60-30 W 68.75 ВС N 80-30 E 125.90 СА

A: Given data in question  Bearing  Distances  Closed Traverse  To find out  Angle  Distance  Note…

Q: S 45 deg E is converted to an azimuth of A 135 B 125 115 145

A: The given bearing is in terms of Quadrantal bearing. Azimuth is the angle subtended with North in…

Q: Please explain why we say (2n -1)As'

A: Solution: The long term stresses in the compression reinforcing steel will be affected by the creep…

Q: Determine the moment of inertia Ix of the shaded area about the y axis. as the following procedure:…

A:

Q: Discuss about NAVD88?

A: Answer Introduction A geodetic reference system is a system that is used to measure the correct…

Q: ∆у = ду 5WL3 384Е (5 ×3758.0698kg x33m3) (384 X200GPa x39.2x106 mm4

A:

Q: The following are ordinates of 5hr UH. Derive and plot FH due to excess RF of 60mm

A: Since the ordinates of 5hr UH is not mentioned assuming it to be m3/s Rainfall excess (n) = 60 mm…

Q: ?근 d=0:02 m 7m Lalom Uso-2% Frnd Z 2.

A: Given:pressure at point 1    P1=104 KN/m2  and HEad Z1=7 m   and velocity V1=0at point 2    P2=0…

Q: Questions: Given: g = 9.81m/s^2 W = 1100kg/m^3 Weight of beam AC = 0.08 kN/m Find the following: 1.…

A:

Q: Station B.S. H.I. F.S. Elevation Remarks BM1 71cm 66cm-72cm 32cm-37cm 34cm-36cm 66.5cm-62.4cm 100…

A: Note:- As the values of B.S. and F.S. are given in intervals so, take the values of the B.S. and the…

Q: Pls draw a SFD and BMD for the following picture.

A:

Q: Determine degree of external indeterminacy

A: Given data : Number of external support reaction (R)=3+3+3=9

Q: Obberved beaning computer Correstien Adjusted values Internal Porward BacK angle Beaning Begring…

A:

Q: Required to find: Tabulate the computed values accordingly. Length, Calculated Bearing LATITUDE…

A:

Q: Determine the moment of inertia Ix of the shaded area about the y axis. as the following procedure:…

A:

Q: Problem#1: y Determine the following: 4 40mm 16 50mm a) Location of centroid from x and у-ахes. b)…

A:

Q: Sketch the qualitative deflected shape for both frames

A:

Q: H.W-1 Calculate the interior angels of the following travers: Line Fore bearing (F.B) АВ 130° 14' ВС…

A: Given:- Using the principles of geometry unknown angles have been calculated Alternative interior…

Q: Find the coordinates of points A, B, C, D and E by adjusting this traverse. Complete all cells in…

A: Given data sheets are not sufficient to solve the problem

MATLAB

MATLAB software is a registered trademark, multi-model programming language, and numerical computing environmental system created by MathWorks. 'MATLAB' is the short-form of "Matrix Laboratory". The MATLAB software permits the utilization of matrix operations, graphical representation of data, execution of algorithms, development of user interface, and linking programs created in other languages. Even though MATLAB is developed mainly for numerical computing, there is an optional toolbox that uses a symbolic engine known as MuPAD giving access to all the symbolic computing abilities. In addition to this, a Simulink package delivers graphical multi-domain simulation and design that is model-based for embedded and dynamic systems. MATLAB users are spread worldwide across the world and use MATLAB extensively.