PROBLEMS 237. The lower ends of the three bars in the figure are at the same level before the rigid homogeneous 18Mg block is attached. Each steel bar has an area of 600mm² and E-200GPa. For the bronze bar, the area is 900mm² and E-83GPa. Find the stress developed in each bar. BRONZE 1.6M STEEL 1M 18Mg STEEL 1M TECHN

PROBLEMS 237. The lower ends of the three bars in the figure are at the same level before the rigid homogeneous 18Mg block is attached. Each steel bar has an area of 600mm² and E-200GPa. For the bronze bar, the area is 900mm² and E-83GPa. Find the stress developed in each bar. BRONZE 1.6M STEEL 1M 18Mg STEEL 1M TECHN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

F13-3. Determine the state of stress at point A on the cross section of the beam at section a-a. Show the results in a differential element at the point. 30KN 'as m'0.5m Но mm- 10 mm so mm 180 mm 10 mm- 10 mm Section aa
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
Prob 1. The rigid bar below is supported by a pin and two rods and must support a load of 100 kN is placed 3 m from A. The brass (Ebrass = 85 GPa) rod has a cross section of 30 x 30 mm and the copper (Ecopper = 120 GPa) rod 20 x 20 mm. Determine the normal stress and deflection of both bars. 1.5 m 2 m B -copper 100 kN brass- 3m 3 m E
Q4) Determine the maximum shear stress acting in the fiberglass beam at the section where the internal shears force is maximum. (tı=15 mm, t2=20 mm, h=150 mm, b=50 mm) 。王! 20 kN/m A |-b-| to 2 m 2 m - 2 m
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm, If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 2. A 200mm 250mm 300mm 30 N-m 20 N-m 80 N-m O 0.94MPA O 4.68MPA O 187MPA O 2.81MPA
1) DETERMINE TENSILE BENDING THE CROSS-SECTION BELOW. SOKN 20KN/m 3m THE MAXimum STRESSES OF THE B 30 кн/т Gm COMPRESSIVE Ано THE BEAM BEAM GIVEN 150MM SHOWIN 30mm 180mm 30mm
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
The Figure below shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 800 mm² for AB and 400 mm² for AC. Determine the maximum safe value of W (kN) if the working stresses are 110 MPa for AB and 120 MPa for AC. ... B 40 deg. A 60 deg. A) 38.90 в) 55.30 61.70 76.2
Two reds vertically connect beam figure. Pcint A is fxed s shinged connected If the rod on the right is heated by 18 degree Celsius 2 m - 2 m 2 m Use E-200 GPa, linear of coeff cient expansion = 11.7x1o per degree celsius and A4509 mm Compute for the deformation of the right rodin mm Select the correct response 0.0234 mm 0.0842 mm 00468 mm 0.117 mm
Problem 1: The rigid bar ABC is supported by AD and BE. Determine: a. Inclination of member ABC after loading b. 8 at point E Members Properties: Member Materials Modulus Cross- sectional Area of Elasticity AD Aluminum 70GPA 450mm2 ВЕ Steel 200GPA 550mm2 E O •Im O:3m 45kN. t 0 4m
Find the diameter of dAB dec bar if the stress equal to 0.15GPA C 120cm B 125kN 125KN 90cm A 60kN
Determine the maximum force P that can be applied to the specimen. The bar is made from steel and has an allowable stress of 150 MPa. 2R = 5mm R = 20mm- PP 150mm -6mm