Problem Three A closed loop feedback control system for a DC motor with speed control is shown below. Determine the output speed response C(s) when the input is a unit step function. CLS) R(S) St2 S+2 5+3

Problem Three A closed loop feedback control system for a DC motor with speed control is shown below. Determine the output speed response C(s) when the input is a unit step function. CLS) R(S) St2 S+2 5+3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights.
Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights. design the single-phase, full-wave, ac/ dc converter. show design specifications, the reason for DC motor selection. correct manual circuit, and correct automatic closed-loop control circuit
A DC chopper is used in regenerative braking mode of a dc series motor. The dc supply is 600 V, the duty cycle is 70%. The average value of armature current is 100 A. It is continuous and ripple free. What is the value of power feedback to the supply ?
A 48kW, 600V, 1500 rpm separately excited dc motor is controlled by single phase semi-controlled converter. The resistance of the armature is 192 and of the field is 1450. The field circuit is controlled by a single phase fully controlled converter and its firing angle is set to 20. The AC supply voltage to the armature and field converters is a single phase 220V, 60 Hz. The voltage constant is 0.946 V/A rad/s. If the armature converter firing angle is 45 and the speed is 1200 rpm; calculate the armature current and the developed torque.
Q6/ Answer the following questions: 1. Define the DC motor drive 2. Classify the DC motor drive 3. How can be controlling on the speed of DC motor 4. Numerate the types of AC-DC converter 5. Draw the circuit of single -phase converter on separately excited DC motor 6. Write the equations the following: I. Speed(W)= II. Torque developed(Td): III. Vm=..
1) P.f of inductive load is corrected by connecting . . across it. .... ...... 2) Open circuit test measures . losses. 3) The output variables of a motor are and ........ ... .... 4) For a motor output power is given by ...... 5) Flux control, voltage control, and armature control are three methods for ....... of dc motor. 6) A transformer takes 100V at primary and gives 50V at secondary, its turn ratio equals 7) The given set of equations represents . . Ea – laRa = Vr , la = IL , %3D Rf 8) The given set of equations represents. la = !, + IL, VT Rf Ea – laRa = Vr , 9) The given set of equations represents . Ea – laRa – IseRse = Vr, la = Ise = l, %3D | 10). .. has more initial torque than shunt dc motor.
The input current to a 220v, compound motor at no load is 6 A. The shunt field circuit resistance is 220 ohms; the armature resistance is 0.10 ohm and the series field resistance is 0.80 ohm. What is the SPL? A. 1153.31 W B. 1066.22 W C. 1232.54 W D. 1073.25 W
Interpret the statement with a mathematical calculation/proof, “The same step angle of 4.5° can be achieved with both the micro-stepping and switched reluctance stepper motors." [CO-2, C3]
1. Single phase full converter is used to control the speed of separately excited DC motors. AC supply voltage is 208 V. Motor armature and field resistance are 0.5 2 and 345 2 respectively. The field current is also controlled by a full converter and the field current is set as the maximum possible value. Motor voltage constant is 0.7 V/A-rad/sec. If firing angle is 45° and armature current is 55 A, determine the angular speed of the motor. Assume armature and field current are ripple free.
A PWM signal is sent to a permanent magnet DC motor through an H-bridge circuit. The PWM frequency is 100 kHz, the DC voltage source is 16 volts, and the specification of the motor is given as: voltage = 16 volts, no load speed = 1500 RPM, holding torque = 2 Nm. a. Draw the voltage signal delivered to the motor when the duty cycle is 20% and 80% (at least draw for 5 periods). Calculate the speed of DC motor when the duty cycle is 20% and 80%. b. C. Estimate the output power when the duty cycle is 20% and 80%. Assume that the motor efficiency is 100%.
A synchronous machine is a three-phase, two-pole machine with 36 stator slots and 5/6 full-pitched balanced armature windings. Each phase winding is made up of eight identical coils connected in sequence. Balanced three-phase 66 Hz currents with a peak amplitude of 16 A are used to drive the stator phases. a) What is the basic stator space mmf's maximum amplitude? (A.turns) b) How fast does the fundamental stator space mmf rotate mechanically? (rpm) c) What is the third-harmonic stator space mmf's maximum amplitude? (A.turns) d) What is the fifth-harmonic stator space mmf's maximum amplitude? (A.turns) e) How fast does the fifth-harmonic stator space mmf rotate mechanically? (rpm)
L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no