Problem: The outer diameter of the thin walled vessel is 400 mm. The external pressure and internal pressure is 8 MPa and 5 MPa resepctively. a. If the allowable stress is 100 MPa, what is the required thickness of the vessel? b. If all the pressures given will be replaced by an internal pressure of 10 MPa and thickness of the wall is 12 mm, what is the critical tensile stress of the wall?

Problem: The outer diameter of the thin walled vessel is 400 mm. The external pressure and internal pressure is 8 MPa and 5 MPa resepctively. a. If the allowable stress is 100 MPa, what is the required thickness of the vessel? b. If all the pressures given will be replaced by an internal pressure of 10 MPa and thickness of the wall is 12 mm, what is the critical tensile stress of the wall?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem (A) Find the thickness of metal necessary for a cylindrical shell of internal diameter 160 mm to withstand an internal pressure of 8 N/mm². The maximum hoop stress i the section is not to exceed 35 N/mm² probaken (b).Determine the maximum and minimum hoop stress across the section of a pipe of 400 mm internal diameter and 100 mm thick, when the pipe contains a fluid at a pressure of 8 N/mm². Also sketch the radial pressure distribution and hoop stress distribution across the section
a.) What is the normal force distributed to Stainless Steel Solid Post 'A' (in kips)? b.)What is the normal force distributed to Red Brass Hollow Tube 'B' (in kips)? c.)What is the normal stress produced in Stainless Steel Solid Post 'A' (in psi)? d.)What is the normal stress produced in Red Brass Hollow Tube 'B' (in psi)?
Problem 3.1. A 1-in.-diameter solid bar (1), a square solid bar (2), and a circular tubular member with 0.2-in. wall thickness (3), each supports an axial tensile load of 5 kips. (a) Determine the axial stress in bar (1). (b)If the axial stress in each of the other bars is 6 ksi, what is the dimension, b, of the square bar, and what is the outer diameter, c, of the tubular member? t = 0.2 in. 1 in. (1) (2) (3)
d. Secant modulus at a stress of 62 ksi.e. Tangent modulus at a stress of 65 ksi.
A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A.
Determine maximum shear stress
A threaded steel rod (Es = 210 GPa, dr = 12 mm, αs = 12 x 10-6/˚C) is held stress free between rigid walls by a clevis and pin (dp = 15 mm) assembly at each end. If the allowable shear stress in the pin is 45 MPa and the allowable normal stress in the rod is 70 MPa, what will be the maximum permissible temperature drop ΔT?
Problem 1 Please choose the correct answer and also write down your solution. (1) A cylindrical tank is required to contain a gage pressure 630 kPa. The tank is to be made of A516 Grade 60 steel with a maximum allowable normal stress of 150 MPa. If the inner diameter of the tank is 2.8 m. what is the minimum thickness of the wall? a. 11.76 mm b. 5.88 mm c. 11760 mm d. 0.00588 mm (2) A cylindrical tank is made of A516 Grade 60 steel with a maximum allowable normal stress of 150 MPa. If the inner diameter of the tank is 4.1 m and the thickness is 1.5 cm. What is the maximum allowable gage pressure? a. 1.097 MPa b. 549 kPa c. 109.76 MPa d. 109.76 kPa (3) A spherical pressure vessel is required to contain 1.4 m³ of compressed natural gas at 21 MPa. If the tank is made of A516 Grade 60 steel with a maximum normal stress 150 MPa. What is the required thickness of the tank wall? a. 97.16 mm b. 9.716 mm c. 4.858 cm d. 53.47 mm
Brass ninum Problem 2 Two 10-kN forces are applied to a 20 x 60-mm rectangular bar as shown. Determine the stress at point A when (a) b = 0, (b) b = 10 mm, (c) b = 25 mm. 10 mm 10 mm 30 mm 10 kN 30 mm 10 kN 25 mm
A 12 mm thick steel pipe with inside diameter of 600 mm conveys water under a head of 350 m. a. Calculate the tensile stress (in kN/m) in the pipe wall. b. Calculate the stress (kPa) in the pipe wall if the head is increased to 500 m of water. c. Calculate the required thickness (mm) under a head of 500 m if the allowable tensile stress of the pipe is 123 MPa and assuming that the joints are 75% efficient.
A compressed gas cylinder for use in mechanical engineering laboratory has an internal gage pressure of 8 Mpa at the time of delivery. the outside diameter of the cylinder is 30 cm. if the steel has an allowable stress of 90 Mpa. what is the required thickness of the wall in centimeter? is it considered a thin walled? [chacking: thickness/inside raduis
Determine the outside diameter of hallow steel tube that will carry a tensile load of 500kN at a stress of (11+150) MPa. Assume the wall thickness to be 1/10 of the outside diameter *