Problem Statement Based on Problem 4-151 from the textbook. The pipe assembly is subjected to the action of a wrench at B and a couple at A. Simplify this system to a resultant wrench and specify the locaiton of the wrench along the axis of pipe CD, measured from point C. F = 42.8 N 0.6 m X -0.8 m (60k) N 0.25 m {–40i} N B 0.25 m - Fi 0.3 m 0.3 m 0.7 m- V-60k) N Fi 0.5 m D y

Problem Statement Based on Problem 4-151 from the textbook. The pipe assembly is subjected to the action of a wrench at B and a couple at A. Simplify this system to a resultant wrench and specify the locaiton of the wrench along the axis of pipe CD, measured from point C. F = 42.8 N 0.6 m X -0.8 m (60k) N 0.25 m {–40i} N B 0.25 m - Fi 0.3 m 0.3 m 0.7 m- V-60k) N Fi 0.5 m D y

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Equilibrium of Concurrent Force System. The piston of a reciprocating engine exerts a force of 175 kN on the crosshead when the crank is 45° (angle B) past TDC. If the stroke of the piston is 800 mm and the length of the connecting rod is 1.80 m, find the guide force and the force in the connecting rod. Hint: 1=½ stroke; Angle o may be solved using Sine Law in AACO. K= Compressive Force in the connecting Rod E= Piston Effort 70 120 F, = Guide Force Fig. P-1 Fig. P-2 a Tools: EF cos0=0; F sin .=0. R = Ev)* + (E#): ; R 771 =- : tane = sin A sin B sin C
EXAMPLE TL ROBOT - In a TL robot, assume that the origin of global coordinate system is at J2 · Determine the coordinate of the ef point if the joint twist by an angle of 30 degrees and the variable length is Im. · Determine the variable link length and angle twist if the ef is located at (0.7071,0.7071) J2(X2. Y2) Ean + (x, y) Jq(X1, Y1)
te F B (0,0,0) <3 of 3 An old wooden telephone pole with a single cross member was blown off center during a recent storm To temporarily stabilize the telephone pole, a repair crew has attached a cable from the end of the cross member to an eye-ring stake anchored in the ground. (Eigure 3) If the origin O of a coordinate system is placed where the pole meets the ground, the point where the cross member is attached to the pole is A(-1.50, 2.10, 23.9) ft and the point where the cable is attached to the end of the cross member is B(-1.50,-2.90, 26.9) ft. The cable's direction is (1.00-1.00-1.00k) and it has a tension of 145 lb. What is M₁, the moment that tends to twist the telephone pole due to the tension in the cable applied at point B? Express your answer numerically in pound-feet to three significant figures. ▸ View Available Hint(s) M₁ = V ΑΣΦ it vec ? lb-ft
Required information A rope connecting points A and B supports the force Fshown in the figure. Write expressions using Cartesian vector representation for the following. Take L 8 ft and F 12 lb, Part 2 of 6 NOTE: This is a multi-part question, Once an answer is submitted, you will be unable to return to this part. 10 points y eBook B T 30° Hint F Print References T BA : the position vector from B to A. Mc Graw Hill MacBook Air
Q) A simplified model as shown in figure below of a planar robotic arm. You may assume that each segment has length 1.5 m, and the applied force is 250 N. 01 = 35 degree and 02 = 03 = 20 degree. Calculate the moment that the force, F, exerts .about the point A F C A M = -1042 M = -1055 M = -1050 M = -1046
PS2-5 Three forces are acting on the problem. List all of the simplifications that can be used in the problem. What is the simplest problem? F₂ 45° R
Solve Q2-22 using both (a) law of parallelogram and (b) Cartesian vector
The figure below shows a steel structure made up of two pre-assembled segments that are hoisted by a mobile crane using a bespoke lifting frame. Each cable must withstand loads of FAB = FAC = FAD = FAE = 4000 kN. You must provide an accurate answer in scientific standard form with one decimal place only. In cartesian vector and in scalar form, compute the rAB, rAC, TAD & rAE length. 14 m 6m 6 m в 3 m 3 m X
Problem 5: Inputs: F = 81 i lb The force is applied at point A. (a) Use the cross product to compute the moment about point O. Moroa X F. Express your answer as a vector. = (b) Using the right-hand rule, interpret your vector result from the previous step and express this as a number with direction, CW or CCW. Use the absolute value here. (c) Use the scalar approach to compute the moment about point O. If you like, you can use the table we used for the previous problems, but a table is not required for this problem. (d) Do parts (b) and (c) jibe? Yes or no. (0, 3, 0) ft y A O F X
! Required information A rope connecting points A and B supports the force Fshown in the figure. Write expressions using Cartesian vector representation for the following. Take L = 8 ft and F= 12 Ib. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. y B 30° ÜBA : the unit vector from B to A. ÜBA
Find box for the given Plane, where by =120m, d=25m, bz=25m, d2=100m, b3=80m & d3=25 m (Enter only the values in the boxes by referring the unit given in brackets. Also upload your hand written answers in the link provided) b2 dz di bị The value of X= (unit in m) The value of Y= (unit in m) The moment of inertia for sec 1 = lyyi = (unit in m) The moment of inertia for sec 2 = lyy2 = (unit in m4) The moment of inertia for sec 3 = lyya = (unit in m4) The moment of inertia of the given plate = lyy = (unit in m)
Q) A simplified model as shown in figure below of a planar robotic arm. You may assume that each segment has length 1.5 m, and the applied force is 250 N. 01 = 35 degree and 02 = 03 = 20 degree. Calculate the %3D moment that the force, F, exerts .about the point A F A. M = -1042 O M = -1055 M = -1046 M = -1050 O