A flanged bolt coupling has ten 16-mm diameter steel bolts on 800 mm diameter bolt circle a nd six 20 mm diameter steel bolts on 600 mm diameter bolt circle. Determine the maximum to rque that can be applied without exceeding the shear stress of 60 MPa for each bolt. Use G = 8 0 GPa. Drawing not included in this problem. Is the computed torque safe for the rod connected by the flange in item number 29? Justify yo ur answer by stating your computed data. The allowable shear stress of each rod is 60 MPa and the allowable angle of twist is 4 degrees. The diameter of each rod is 200mm and the length is 6 meters. Use G = 80 GPa. Drawing not i Included in this problem.

A flanged bolt coupling has ten 16-mm diameter steel bolts on 800 mm diameter bolt circle a nd six 20 mm diameter steel bolts on 600 mm diameter bolt circle. Determine the maximum to rque that can be applied without exceeding the shear stress of 60 MPa for each bolt. Use G = 8 0 GPa. Drawing not included in this problem. Is the computed torque safe for the rod connected by the flange in item number 29? Justify yo ur answer by stating your computed data. The allowable shear stress of each rod is 60 MPa and the allowable angle of twist is 4 degrees. The diameter of each rod is 200mm and the length is 6 meters. Use G = 80 GPa. Drawing not i Included in this problem.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer in this format. Sketch: Given: Required: Solution: (Please answer in detailed (step by step). Indicate labels on what you are doing/performing, for example what formula is used) A torque To is transmitted between two flanged shafts by means of four 20-mm bolts. diameter of the bolt circle is 2=150mm. If the allowable shear stress in the bolts is 90 Mpa, what is the maximum permissible torque? Disregard friction between between flanges. The To
A 16 in. diameter motor pulley is running at 600 rpm with a 6 in diameter shaft transmitting power to an agricultural locomotive. If the dimensions of the square key is 0.5 x 3 in, what is the maximum force in the pulley’s belt that can be transmitted if the shear stress is limited to 8500 psi and bearing stress limited to 4000 psi?
Design a flanged coupling that will be able to carry power of 1,500 HP using a factor of safety of 3.3 at 630 rpm. The shaft diameters of the equipment the coupling will connect are both 5 inches. Check your design for the following stresses if N = 3.3 is satisfied: 1. Bolt shearing; 2. Bolt bearing; 3. Shearing of hub from coupling flange; 4. Shear on key; 5. Compression on key; Select dimensions whichever is higher. 6. Calculate also minimum length of engagement of the bolt and nut if these are of the same material. 5 inch dia. shafts coupling to connect the equipment shafts. Note: use 4 bolts only Instructions:
Q-3 A 25-mm-diameter solid round bar has a groove 2.5-mm deep with a 2.5-mm radius machined into it. The bar is made of AISI 1050 CD steel and is subjected to a purely reversing torque of 250 N-m. For the S-N curve of this material, let f= 0.9.
Solve the following problems as stated below. Draw the figure and FBD. PROBLEM A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter dp / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gp = 28 Gpa. R Rs Rb
A flanged bolt coupling consists of eight 10 mm diameter steel bolts on a bolt circle 400 mm in diameter, and six 10 mm diameter steel bolts on a concentric bolt circle 300 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the bolts?
A steel shaft of 2.5 inch diameter rotates at 500 rev/min and transmits 120 hp through a gear. Select an appropriate square key for the gear, while the key material having yield strength of 60 kpsi. Assume a factor of safety of 2.0.. Draw sketch and show all calculations.
A 45 mm diameter shaft is made of steel with a yield strength of 400 MPa. A parallel key of size 14 mm wide and 9 mm thick made of steel with a yield of 340 MPa is to be used. Find the required length of key, if the shaft is loaded to transmit the maximum permissible torque. Use maximum shear stress theory and assume a factor of safety of 2.
. The mean diameter of the driving pulley for a vec-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of frietion between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm.
A gear transmits 560 N of torque to a circular shaft having a diameter of 58 mm. A square key 13 mm on a side connects the shaft to the hub of the gear, as shown in the figure below. The key is made from SAE 1020 cold-drawn steel. Determine the required length of the key, L, to be safe for shear and bearing. Use a design factor of 2.0 based on yield for shear and the AISC allowable bearing stress. Shear plane Hub Shaft Key Shear area = A, =b x L
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
4. A tube composed of a wrought aluminum alloy 6061-T6 is designed to transmit a torque in a control mechanism; however the compressive stress in the tube must not exceed 7000 psi to prevent the tube from buckling. The tube has an outside diameter of 1.25 in., a wall thickness of 0.065 in. and total length of 2.0 ft. Find the maximum torque which can be applied and the angle of twist over the length of the tube at the maximum torque.