Problem: Referring to the structural members of truss in the figure, determine the internal axial stress of each member considering the following sections: AB = square bar (25mm) 3 = BC = rectangular bar (6mm X 50mm) CD = round bar (25mm diameter) BD = steel pipe (30mm outside diameter @ 5mm thickness) Specify if tensile or compressive stress. 800 N 600 N 60° By 4 m D 3 m

Problem: Referring to the structural members of truss in the figure, determine the internal axial stress of each member considering the following sections: AB = square bar (25mm) 3 = BC = rectangular bar (6mm X 50mm) CD = round bar (25mm diameter) BD = steel pipe (30mm outside diameter @ 5mm thickness) Specify if tensile or compressive stress. 800 N 600 N 60° By 4 m D 3 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.4P: Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield...

See similar textbooks

Similar questions

A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress
A suspender on a suspension bridge consist of a cable that passes over the main cable (see figure) and supports the bridge deck, which is Far below. The suspender is held in position by a metal tie that is prevented from sliding downward by clamps around the suspender cable. Let P represent the load in each part of the suspender cable, and let represent the angle of the suspender cable just above the tie. represent the allowable tensile stress in the metal tie. (a) Obtain a formula for the minimum required cross-sectional area of the lie. (b) Calculate the minimum area if P = 130 kN, = 75°, and allow=80 .
Continuous cable A DB runs over a small friction less pulley al D to support beam OABC, which is part of an entrance canopy for a building (see figure}. The canopy segment has a weight W = 1700 lb that acts as a concentrated load in the middle of segment AB. (a) What is the maximum permissible value of load P at C if the allowable force in the cable is 4200 lb? (b) If P = 2300 lb, what is the required diameter of pins A, B, and D? Assume that the pins are in double shear and the allowable shear stress in the pins is 10 ksi.
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb (see figure). The center of gravity of each child is 8 ft from the fulcrum. The board is 19 ft long, 8 in. wide, and 1.5 in. thick. What is the maximum bending stress in the board?
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
Referring to the structural members of truss in the figure, determine the internal axial stress of each member considering the following sections: AB = square bar (25mm) BC = rectangular bar (6mm X 50mm) CD = round bar (25mm diameter) BD = steel pipe (30mm outside diameter @ 5mm thickness) Specify if tensile or compressive stress. 800 N 600 N 60° B 4 m 3 m
A prestressed hollow box cross section is shown in the figure. The area of prestressed reinforcement in the tension zone is 1148 mm2. Use grade 270 for seven wire-strand tendons. fpy = specified yield strength of tendons fpu = specified tensile strength o pre stressing tendons fse = effective prestress after losses fse = 1022 MPa Aps = 1148 mm2 fpy = 0.95fpu fc’ = 34.5 MPa fpu = 1860 MPa a. Compute the Yp factor. b. Compute the stress in prestressed reinforcement at nominal strength. c. Compute for the design moment capacity. d. Compute the effective pre stressing force after losses of stress e. Compute the depth of the compression block. f. Compute the pre stressing steel ratio.
Problem I. In a high-rise building construction, a boom is being used to efficiently transport materials from the ground to a certain level in the building. Shown below is a figure of the boom supporting the load 'P.' Note: P = 209kN 100 mm- -87.5 mm 2P 12.5 mm dia 10 m -10 m At the right is the support detail at B. a) What is the normal stress (in MPa) the boom is subjected to if its cross sectional area is 1174 mm?? b) Calculate the shear stress in the pin (in MPa). c) If the allowable stress in the steel cable AC is 170 MPa, what should be size (diameter, in mm) of the cable to sufficiently withstand the force it is subjected to?