PROBLEM NO. 2: A 4 BY 4 – IN. WOOD – POST BC IS CONNECTED TO A 1 - IN. DIAMETER STEEL EYE – BAR AB TO FORM A HOIST. A LOAD OF W = 7000 LBS IS APPLIED AT POINT B ON THE HOIST. (A.) DETERMINE THE AXIAL STRESSES IN MEMBERS AB AND BC. (B.) DETERMINE THE CROSS SHEARING STRESS IN THE | 1- IN. DIAMETER BOLT AT POINT A. STEEL W în A C WOOD 7' 5'

PROBLEM NO. 2: A 4 BY 4 – IN. WOOD – POST BC IS CONNECTED TO A 1 - IN. DIAMETER STEEL EYE – BAR AB TO FORM A HOIST. A LOAD OF W = 7000 LBS IS APPLIED AT POINT B ON THE HOIST. (A.) DETERMINE THE AXIAL STRESSES IN MEMBERS AB AND BC. (B.) DETERMINE THE CROSS SHEARING STRESS IN THE | 1- IN. DIAMETER BOLT AT POINT A. STEEL W în A C WOOD 7' 5'

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.13.1P

See similar textbooks

Similar questions

One plate of size 100 mm x 12 mm is lap joined to another plate of size 200 mm x 12 mm by fillet weld of size 10 mm. Lap length is 100 mm. Fillet weld is provided on all the three sides of the smaller plate. Determine the maximum axial tension the joint could carry. Assume the plates are of mild steel of grade 250 N/mm?.
HiW@ Draw S.f.n and BiMin for beam shown by Naphial methds Anst hinge %3D M= 9 W.m 3m 2m 3m Mmny = -6 IW.m
Student A B D H Number 201780130 2 1 7 8 1 3 Evaluate the following variables and use them as given in the following problems. 200 if I is even, 250 if I is odd (D + G)*10 (H + I/2, if in case the result is zero, use 3 (A +C + E)*2 (P + M)*20 H + 5 M Q %3D 50(E + G + 1) II II || || || |||| ZNPORX
Determine the shear Load that act on the fillet weld that joining two plates together if the working stress is 11300 Ib/in? Throat
A 5/8 in- diameter steel rod AB is fitted to a round hole near end C of the wooden member CD. For the loading shown, which of the following nearly gives the bearing stress in the wood in psi?
Compute the available block shear strength of the gusset plate. a. Use LRFD. b. Use ASD. PL ½ x 6 A36 steel Weld t=½"
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
A 22.2 mm diameter bolt having a diameter at the root of the threads of 18.6 mm is used to fasten two timbers as shown. The nut is tightened to cause a tensile load in the bolt of 34 kN. (a) Determine the shearing stress in the head of the bolt. (DRAW THE FREE BODY DIAGRAM) (b) Determine the shearing stress in the threads. (c) Determine the outside diameter of the washers if their inside diameter is 28 mm and the bearing stress is limited to 6 MPa. (DRAW THE FREE BODY DIAGRAM)
Shear stress #1- Two blocksy wood, 6Omm nidi ard 30mm thdk, are glued fogether. Det. The maximum value P f the Tengite sfreek 7 The urod is limited f 24° with the hoirontal. to 6mpa ard the shearing stress on The glued joint and the sheanng sfres parallie to the Cimited to 6mpa. The mafies an angle is 4 m Pa. rglued, joint Gomm 600 720mm
Figure 1.5 m E -2 m- 3 kN D B -2 m 1 of 1 Identify the zero-force members in the truss. Check all that apply. BE DE CD AB AE BD BC Submit Drouido Foodbook Request Answer
1-102 Determine the intensity w of the maximum distrib- uted load that can be supported by the hanger assembly so that an allowable shear stress of Tallow= 13.5 ksi is not exceeded in the 0.40-in.-diameter bolts at A and B, and an allowable tensile stress of allow 22 ksi is not exceeded in the 0.5-in.-diameter rod AB. 3 ft B 4 ft + 2 ft-
SOLVE FOR THE FORCE IN MEMBERS AB, AC, BC, CD, BD, BE, DE, DF & EF. SHOW SOLUTIONS CLEARLY USING METHOD OF JOINTS AND WRITE WELL ALSO SEE LINK UNDER WEEK7 0.8m 2.4m -6KN MEMBER AB AC BC CD BD BE 2m ED DF EF 1m 8KN Av REACTION hinge) EX REACTION @roller) 3m SUMMARY OF RESULTS FORCE 1m 10KN 2.4m 3KN NATURE(I or C)