Problem 2: The accompanying tabulation gives elevations of points over the area of30m by 30 m residential lot. The elevations were obtained using 10m squares. PointA -1 is located in the northwest corner of the lot and D-4 at the southeast corner. Allelevations are in meters.TAANAPoint124178.8182.5183.583.6B183.3185.9193.7187.2182.8188.6191.8189.3D182.5190.4192.6189.5a) Plot the corners using a scale of 1cm = 2m and a contourinterval of one meter.b) All corners designations and corresponding elevations must be indicated,including all vertical and horizontal lines.c) Indicate the elevations of the following index contours: 180m, 185m, `190, andThe thickness of the index contours must be drawn about twice the thickness ofthe intermediate contours.d) Use pencil for the initial plot and the final plot using technical pen.

(a) The scale utilized is 1cm = 2m . The line is displayed underneath. The cycle used to line a line…

Answered: evations were obtained using 10m…

Engineering

Civil Engineering

evations were obtained using 10m squares. PointA ner of the lot and D-4 at the southeast corner. A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4pts In the dam figure with assumed 1 meter strip: water depth D=9m, dam height H=12m, and dam base ...

Q: A machine having a first cost of Po0,000 s computed using constant percentage of the declining book ...

Q: In the design of beams for the limit state of collapse in flexure as per IS: 456-2000, let the maxim...

Q: Prob. 2.3-7. For small loads, P, the rotation of "rigid" beam AF in Fig. P2.3-7 is controlled by the...

A: The change in length of a stressed structural member divided by the initial length of the unstressed...

Q: PLS ANSWER ASAP WITH 3 DECIMAL PLACES

A: Given:- 100mm x 50mm x10mm C250 x 30 C250 x 45 To find:- centroidal moment of inertia

Q: (i.e., Amax < L/360). 60 kN 300 kN-m LA 5 m 5m L= 10 m El = constant E = 200 GPa

Q: Calculate the moment (positive if counterclockwise, negative if clockwise) of the 370-N force on the...

Q: 1. Starting from rest, a particle moving in a straight line has an acceleration of a = (2t - 6) m/s,...

A: QUESTION 1 a = (2t-6)m/s2 it has been asked in the question to determine the particle velocity when ...

Q: Question 1 Show sketches of beam cross sections including bar sizes, arrangement, and spacing. Span ...

Q: The truss is subjected to the loads as shown in the figure. Determine the required cross sectional a...

Q: Steel L= 4 ft A = 0.50 in? E = 29 x 10° psi B L1 L2

Q: find the coordinates of the point in the curve y^2=12x-2y+23 that is nearest to the point P(10,4)

A: To determine the coordinates of the point on the given curve that is nearest to the given coordinate...

Q: Given the following relationships Deflection angle = 16°38’ R=350 m P.I. @6+025.42 Compute the stati...

Q: A doubly reinforced rectangular concrete beam has a width of 300 mm and an effective depth of 500 mm...

Q: Find the distance traveled for the time 0 to (1500+N) sec interval.

A: The values and graph given in the question are as follows: Distance traveled 0 to (1500+N) seconds i...

Q: edule. The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gea...

Q: Instruction: Read and analyze the problem, Find the mean and variance of the sampling distribution o...

A: Step 1

Q: sing cantilever method, determine the maximum absolute axial force in the column in kN due to latera...

Q: The magnetic azimuth of line PQ is 283* 36'. The declination at point P is 4* 20 west. The true bear...

Q: The time taken to construct a building was from April 1992 to September 1993. In September 1996, the...

Q: For the drag coefficient relationship given in Problem 6.24, if the units of Fd , V, A, and Cd , are...

A: Given:- The units of Fd , V, A, and Cd , are expressed in N, m/s, m2 , and unitless To find:- approp...

Q: Discuss the uses for topographic surveys.

A: A topographic ground assessment might well be required to identify distinctive aspects and altitudes...

Q: From the constant head permeability test, the following values are given: Void ratio of specimen Len...

Q: m, and 125.3 m, respectively. Assuming uniformity of slope between sketch). The alevation at the cen...

A: E-A=165-62.5 =102.5 Contour interval=20 m Therefore,we will have=102.5/20 ...

Q: a). What is the minimum diamétér of a solid 6m stéél shaft that will carry a shearing stress of not ...

Q: 123kN 98kN/m 60.5kN/m

Q: a fluid flows into a tube, and is discharged at point 2 at atmospheric pressure. The difference betw...

A: Given:- Elevation differance,Z1-Z2=16m Length,L=966m P1=2.5kPa P2=Patm=101.325kPa =0.5mm=0.510-3m =7...

Q: a). What is the minimum diamétér of à sölid 6m stéél shaft that will carry a shearing stress of not ...

Q: A rod 150cm long and of diameter 2.0cm is subjected to an axial pull of 40 kN. If the modulus of ela...

A: Given data : The value of axial pull P=40 KN The value of length of rod L=150 cm The value of diamet...

Q: A rectangular steel block is 3.0 inches long in the x-direction, 3.0 inches long in the y-direction,...

A: Given, Lx= 3 inchLy= 3 inchLz= 4.5 inch Fx= 50 kipsFy= -60 kipsFz= 54 kips Poisson ratio=0.30 E=29×1...

Q: 3. A rigid beam AB rests on the two short posts shown. AC is made of steel and has a diameter of 20 ...

Q: Describe the process by which engineers evaluate alternatives.

A: The advantages and disadvantages of each option are examined when evaluating them. During the evalua...

Q: The 1986 disaster in the former Soviet Union at the Chernobyl nuclear power plant explosion sent abo...

Q: In a 4 cm diameter pipeline carrying laminar flow of a liquid withu = 1.6 centipoise, the velocity a...

Q: 1. An executive receives an annual salary of P600,000 and his secretary a salary of P180,000. A cert...

A: Given - Annual salary = P600000 Salary of secretary = P 180000 To find- Cost of performing task by...

Q: The rigid bar ABC shown in the figure below is hinged at A and supported by a steel rod at B. Determ...

Q: The resultant of the three forces shown is a counterclockwise couple of magnitude 150 kip-ft. Calcul...

A: To find out the magnitude of all forces.

Q: 2) A built-up steel column, consists of W 350 x 90 with two 14 mm thick plates welded to form a box ...

A: Properties of W350X90 Properties of Plate 14x350

Q: WHAT IS THE DIFFERENCE IN SOLVING OR GETTING THE ANALYSIS OF A FRAME USING PORTAL METHOD AND CANTILE...

A: Portal method and cantilever method Both the methods are approximate methods of analysing multistor...

Q: PROBLEM 4 For the figure shown, determine the stresses of the wires and the elongation when the temp...

A: Given data in question UVL Steel and aluminum wires Length Area Modulus of Elasticity Coefficient ...

Q: ed concrete slab. Assume A 36 full lateral support of the lange. Unit weight of concrete is

A: Step 1dead load on beam ⇒DL =1×2.4×0.15×24 kn/m3 = 8.64 kn/m step 2 ultimate factoreed ...

Q: lp me answer the problem question and write it on paper with a complete solution and box the final a...

A: iLook at the % passing through 200=33<35%So, Granular materialsii% passing through 200 =33>25...

Q: Determine maximum principal stress

A: Given data : Normal stress in X direction σX=-11500 psi Normal stress in Y direction σY=-18250 psi S...

Q: Prepare a spreadsheet to compute settlement of square footings using the e@log@p method. Thespreadsh...

A: Given:- Cr/(1 + e0), Cr/(1 + e0) To find:- settlement

Q: Use the substitute member to make a complete analysis of the complex truss shown.

Q: Calculate the interior angels of the following travers: Line Fore bearing (F.B) АВ 130° 14' ВС 50° 2...

A: Given:- The fore bearing for the traverse is given:- Line Fore bearing (FB) AB 130°14' BC 50...

Q: (a) A material can be made stronger by applying plastic deformation-explain with the help of strain ...

A: Strain hardening mechanism : When a metal is stressed past its yield point, it is called strain hard...

Q: The U-tube of Figure A contains mercury (s = 13.6) and given an acceleration of 1.22 m/s to the righ...

Q: 4 pts In the dam figure with assumed 1 meter strip: water depth D=9m, dam height H=12m, and dam base...

Q: The effective width of a reinforced cóncrete T-beam flange under compression, according to IS: 456-1...

A: The effective width of a reinforced concrete T- beam flange under compression? Given data - Lo = ...

Concept explainers

Room Relationships and Sizes

Residential architecture consists of mostly enthusiastic experts than any other field. The room relationships mainly depict the orientation of various rooms placed for the incoming of maximum natural resources and every room serving their purpose efficiently. For a high-quality lifestyle, the relationships between many parts of the house play a vital role. For instance, to maintain good health and hygiene, the kitchen must be away from toiletries and thus these types of room relationships are unsuitable. Also, the room relationships with dine room and kitchen must be strong for quick accessibility of food items. More exposure to the house plans causes people to feel that they can make a blueprint of their own. Media advertisements and the availability of home improvement stores have spread awareness and educated customers with an advanced sensitivity towards design and arrangement.

Question

Problem 2: The accompanying tabulation gives elevations of points over the area of
30m by 30 m residential lot. The elevations were obtained using 10m squares. PointA -
1 is located in the northwest corner of the lot and D-4 at the southeast corner. All
elevations are in meters.
TAANA
Point
1
2
4
178.8
182.5
183.5
83.6
B
183.3
185.9
193.7
187.2
182.8
188.6
191.8
189.3
D
182.5
190.4
192.6
189.5
a) Plot the corners using a scale of 1cm = 2m and a contourinterval of one meter.
b) All corners designations and corresponding elevations must be indicated,
including all vertical and horizontal lines.
c) Indicate the elevations of the following index contours: 180m, 185m, `190, and
The thickness of the index contours must be drawn about twice the thickness of
the intermediate contours.
d) Use pencil for the initial plot and the final plot using technical pen.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 7: the corners of the building lot ABCDE are shown in rectangular coordinates (N, E). 1) What is the area of the lot in square feet? 2) What is the distance from A to C? 3) What is the angle B-A-C? 4) Is AC parallel to ED? Explain. (80N, OE) A, (ON, OE) E (ON, 50E) (80N, 100E) (40N, 100E)
2. The four corners M, N, O, and P of a rectangular building having the coordinates given in the table, are to be set out from control station Q by a total station instrument. Calculate the WCB and distance to establish each corner of the building. The coordinates of Q are E 938.945 m, N 825.484 m. Corner East North 624.037 215.878 1568.761 635.225 1249.965 1334.136 429.649 1198.236 MNOP
2) A surveyor sets up a transit at P which is located in the middle portion of a four- sided tract of land and reads directions and measures distances, as given below, to the five corners. Find the area of the tract, in square meters. LINE BEARING DISTANCE N 41030' W Ν 38010, Ε S 70°20' E S 60°15' W AP 410.52 m ВР 532.18 m CP 450.75 m DP 590.08 m
4. Lines of levels to establish the elevation of a point are run over four different routes. The observed elevations of the point with probable errors are given below. Determine the most probable value of elevation of the point LINE OBSERVED ELEVATION (m) PROBABLE ERROR (m) 1 219.832 +- 0.006 2 219.930 +- 0.012 3 219.701 +- 0.018 4 220.021 +- 0.024
Given the following data of a tract of land, find the area of the Tract ABCDP. The parcel of land is divided into two parts by a line through A with a bearing of N 75° 30' E. LATITUDE (m) DEPARTURE (m) LINE AB 490.71 47.27 BC 587.12 608.89 CD -327.41 786.78 DE -1002.76 218.32 EF -122.67 -1116.62 FA 375.01 -544.64 Tract ABCDP 75 30 Dividing Line Tract PEFA Trial Line Copy Share Select all Web search Dictionary 91.03 Hectares 5 113.71 Hectares 86,54 Hectares O 95.38 Hectares
. Problem 1 Compute the area within the following traverse using the Coordinate method and CHECK by the DMDS method Balanced Coordinates Course Dep Lat Point X Y AB -226.9846 98.7106 A 709,489.434 709,262.449 709,176.011 709,061.165 709,361.616 708,846.452 G 709,568.788 709,682.105 I 709,563.827 121,072.089 121,170.800 120,992.637 120,797.489 120,807.032 120,287.159 120,244.663 119,715.939 120,610.402 BC -86.4386 -178.1623 CD -114.8457 -195.1486 C DE 300.4512 9.5436 EF -515.1646 -519.8733 日 FG 722.3360 -42.4958 F GH 113.3175 -528.7245 HI -118.2782 894.4631 IA -74.3929 461.6870
Q11: The four comers A, B, C, and D of a portal frame factory having the coordinates Satisfactory given in Table 7, are to be set out from control station P by a total station instrument. Calculate the WCB and distance to establish each comer of the portal frame factory. Y N Table 7: Corner Easting (m) Northing (m) A 117.984 92.849 82.629 128.204 33.132 78.707 68.487 43.352 The coordinates of P are E 110.383 m, N 81.334 m. (PC 3.4, 4.3, RS 5, RK 6.5) A:
1. Using the corrected/adjusted latitudes and departures below. Determine the coordinates of the points if the Northings and Eastings on point 1 are 991422.35 meters, 785547.11 meters, respectively. Please show your solution. Dep (m) -185.48 LINE Lat (m) 1-2 -321.18 2-3 165.75 -44.08 3-4 172.97 0.29 4-1 -153.24 364.97
Compute by DMDs the area in hectares within a closed-polygon traverse ABCDEFA by placing the X and Y axes through the most southerly and most westerly stations, respectively. Departures and latitudes (in meters) follow.AB: E dep. = 30, N lat. = 40; BC: E dep. = 70, N lat. = 10; CD: E dep. = 30, S lat. = 50; DE: W dep. = 60, S lat. = 40; EF: W dep. = 90, S lat. = 30; FA: E dep. = 20, N lat. = 70
B. Profile Leveling Station BM Road 0+00 0+20 1+00 2+00 2+60 3+00 3+90 4+00 4+35 TP1 5+00 5+54 5+74 5+94 6+00 7+00 TP2 8+00 9+00 9+25.2 9+25.3 9+43.2 BM Store Σ BS 10.15 7.34 2.56 HI FS 11.47 5.26 0.76 IFS 9.36 9.80 6.50 4.30 3.70 7.10 11.70 11.20 9.50 8.40 11.08 10.66 11.06 10.50 4.40 1.20 3.90 3.40 4.60 2.20 Elevation 360.48 ft
Convert 48 15' 26" to centesimal units O 43.4315 O 53.6191 O 31.2254 O 56.8024
Q7) Calculate the coordinates. Check whether the error is acceptable. Make corrections. N 59.0701g S2 145.5558g S1 161.51849 A x=315.122m $3 S6 120.6210g 167.8089g S4 F S5 Y (m) x (m) Дх B (grad) a (grad) S (m) Ay STATION A 137.619 214.077 170.542 D 189.664 225.219 F 156.907 A 8 y=74.056m