Please answer using Conjugate-Beam Method and show complete solution. Problem no. 1 Determine the slope and the displacement at theend C of the beam. .8 kN4 kNACDВ.3 m-3 m-3 m

Answered: Image /qna-images/answer/c35d95ca-44ce-421a-a879-8693dea06eb6.jpg

Answered: Problem no. 1 Determine the slope and…

Engineering

Civil Engineering

Problem no. 1 Determine the slope and the displacement at the end C of the beam. . 8 kN 4 kN A |C D B- - 3 m -3 m -3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 1081 MPa…

Q: 20mm Square plate is subjected normal stresses as illustrated. Modulus of Elasticity, E = 704 MPa…

Q: 4. Which among the following is the correct format for Rayleigh's method? a) D = f(l,p,µV,g) b) D-…

A: Which among the following is the correct format for Rayleigh’s method?a) D = f(l,ρ,μV,g)b) D =…

Q: QUESTION 2 PROBLEM 2: Calculate the components of the forces at B and C. A D E F b Given: P= 21 kN a…

Q: Problem Instructions: The cutting plane should pass through the midspan of the beam. From the…

A: Given data :

Q: Suppose we have a uniform beam that is 3.73 metres long has a flexural rigidity of 34301 Nm². N Find…

Q: -Wfat is the minimum diamefer Ha folid Steel shaft that ll not twist thru more than 3° in á G-m…

Q: Note: Please show all of the free body diagrams used and also show the complete solution. The beam…

A: Deflection will be determined by the first mentioned method i.e. double integration.For other…

Q: A flat steel bar, 26 mm wide by 3 mm thick and 1.3 m long, is bent by couples applied at the ends so…

A: First task To calculate Radius of curvature using central deflection given in the question.…

Q: Required: Vertical displacement at C PL AE E MB = 0 Fal (6m) – 50kN (2.5m) =0 Fa = 20.83kN %3D Steel…

Q: Solve the internal forces on the given beams.

A: Consider the free body diagram of the given beam as shown below.

Q: In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards.…

A: Answer We are given Tensile working stresses for plywood = 1245 psi Tensile working stress for the…

Q: Solve the internal forces on the given beams.

Q: Find the coefficient of friction if normal force is 1000 N and friction force is 555 N

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: Determine the maximum forgue tfal can be applied to a hollow circular sfeel shaft ť I0omm outside…

A: TJ=τR=GθL for first condition TJ=τR where T=? τ=60MPa R=50mm J=π32Do4-Di4=5.8X106mm4 put all values…

Q: Given: • Rod A: Length = 40mm Rod B: Length = 60mm Determine: ● ● Area = 3 cm x 3 cm Area = 4 cm x 4…

A: Given data P = 100 KN EA = EB = 200 GPA = 200 × 103 N/mm2 Area of rod-A (AA) = 3cm × 3cm = 30mm…

Q: Steel railroad rails 10 m long are laid with end-to-end clearance of 5 mm at a temperature of 18°C.…

Q: Q2: Use dimensional analysis to derive an epresion for the power developed by an engine in terms of…

A: Given Power=P Torque=T Rotation speed=ω

Q: Determine the coordinates of the mass center of the welded assembly of uniform slender rods made…

A: Determine the coordinates of the mass center of the welded assembly of uniform slender rods made…

Q: The beam has a Young's modulus of Eo =100 GPa, a length of 1 = 4 m and 2nd moment of area of I₂ = 4…

A: Given: E = 100 GPa = 100 x 109 N/m2 Iz = 4 m4 l = 4 m w = 100 N/m

Q: Question 3 An 4.3 meter aluminum square wire is hanging vertically. A tensile load of 350 KN is…

A: As per bartleby policy i can do only one question at a time. Please upload again other questions.…

Q: coefficient on force is 555 N of friction if normal

A: Given data- Normal force (N) = 1000 N Friction force (f) = 555 N

Q: free body diagrams, equations used, problem setup etc. so that your

A: Given: Allowable shearing stress = 60 MPa To find the smallest permissible diameter of the solid…

Q: Problem 1. The beam is shown below with a cross-section of 350 mm x 500 mm. Assuming modulus of…

Q: eral steps that -node and mes

A: solution of above problem is below:

Q: Problem 7.1. An acrylic rod is 200mm long and 15mm in diameter. If a tensile axial load of 300N is…

Q: Show complete solution e Determine the following unknowns using Double Integration Method. consider…

Q: Do this handwritten I have attached the final answer too

Q: Torques are applied to the solid shaft shown. (a) What is the maximum shearing stress in the shaft,

Q: Sfeel prope ller shaft is to foan&mit 45 mw 43 H2 without exceeding oa shearing sfress 750 mpa tr…

A: f= 3Hz P=4.5MW L=26d G=83GPa

Q: (4) As shown in the figure, the three steel plates are subjected to tensile force P, and seven…

A: When two plate is connected by single plate at middle and it is connected by means of rivet or bolt…

Q: The prismatic block with dimensions a * b * c is placed in a rigid space of the same size. Find the…

A: Finding out the force to shorten the block by 2mm.

Q: Question- A circular shaft of diameter 'D' is made of a material for which Young's Modulus of…

A: Given data- A circular shaft of diameter D, Young modulus=E, Poisson's ratio=v, To Find- The ratio…

Q: Q1) Three bars each made of different materials are connected together and placed between two walls…

Q: You are required to qualitatively analyse the following structures. On the diagrams provided below…

Q: Find the coefficient of friction if normal force is 1000 N and friction force is 555 N

Concept explainers

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.

Question

Please answer using Conjugate-Beam Method and show complete solution.

Problem no. 1 Determine the slope and the displacement at the
end C of the beam. .
8 kN
4 kN
A
C
D
В.
3 m
-3 m
-3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 7.5m cantilever beam shown carries a 115KN/m uniform load. Point A is free end while point B is fixed support. Using Double Integration Method with origin at point A, calculate the value of EIy' at the free end in KN-m2. Express your answer in 2 decimal places. Please show complete solution
Q2 The beam shown in Figure Q2 is loaded with a triangular distributed load from A to B, and a uniform distributed load from B to C. The cross-section is a hollow rectangle, 60 mm x 120 mm, with constant wall thickness of 8mm. The material is Steel, with a Young's Modulus, E = 200 GPa, Poisson's ratio, v = 0.3, and co-efficient of thermal expansion a = 12 x 10-6/°C. |x w = 0 kN/m A ford K Q2 contd. 2m B >> ← Cross-section (a) Draw a Free Body Diagram of the beam and determine the reactions at the supports. 120 mm (b) Use the Method of Sections to determine expressions for the bending moment along the beam length. MEE1004/2021 (c) Determine the normal stress (a) on the bottom of the beam at x = 2.5 m. State whether it is tensile or compressive. (d) If the loaded beam is subjected to a temperature increase of 50°C, determine the transverse strain, &, at the bottom of the beam at x = 2.5 m.
Shown in the figure attached is a beam. Given the loading and support condition and assuming that EI is constant for the beam, determine the (a) The equation of the elastic curve, (b) The deflection at the left end of the beam, and (c) The support reactions By and MB.
Express your intermediate answers with FRACTION and simplify your FINAL answers up to TWO DECIMAL PLACES.BOX your FINAL ANSWERS
Discuss Schmertmann’s method
Example 1: solve the equation = 6x (2y – 1)given the ax? du %3D boundary condition that at x = 0, = sin2y and u = cosy.
Both ends of the beam are guided or slider support not Fixed support. Plz, solve this problem using stiffness Method and show all the step and alsi draw SFD and BMD My last two digits of my reg.no: 95 Structural Analysis-2
i need the answer quickly
How do I find the x and y components, the load and the t or c for each member. Also could you put the answer like it is on the image. Also please show work thank you.
I need the answer as soon as possible
Please solve it within 30 minutes please i need help formulas are also attached