In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1245psi for the plywood and 725psi for the boards. The working shear stress for the glue is 52psi. P 6.25in 1.95in ·b b Determine the dimension b so that the joint is as strong as the boards. P inches in 2 decimal places.

In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1245psi for the plywood and 725psi for the boards. The working shear stress for the glue is 52psi. P 6.25in 1.95in ·b b Determine the dimension b so that the joint is as strong as the boards. P inches in 2 decimal places.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

4. The two pieces of wood, 2 in. by 4 in., are glued together along the 40° joint shown in Figure 4. Determine the maximum axial load P that can be applied if the shear stress in the glue is limited to 250 psi. 600 N 30 150mm FIGURE 4 100 mm 600 N
4. The two pieces of wood, 2 in. by 4 in., are glued together along the 400 joint shown in Figure 4. Determine the maximum axial load P that can be applied if the shear stress in the glue is limited to 250 psi. 600 N a 30° 100 mm 600 N 150mm FIGURE 4
3.* Figure 3 shows a tapered glued joint between two pieces of wood subjected to a tensile force. If the glue can sustain a maximum average tensile stress of 30 MPa and/or a maximum average shear stress of 50 MPa, what is the maximum angle that will permit the joint to transmit a tensile force F = 25 kN with a safety factor of 3.0? [Ans: 23⁰] F 1.6 A 3.4 Ө all dimensions in cm F
A joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1200 psi for the plywood and 700 psi for the boards. The working shear stress for the glue is 50 psi. Determine the dimensions b and t so that the joint is as strong as the boards.
A beam is made of four planks glued together. Knowing that the vertical shear in the beam is V = 500 N, determine the minimum required shear strength Tg for the glue. 50 mm 50 mm 50 mm V D B 150 mm 50 mm 150 mm 50 mm
The two wooden members shown, which support a load P, are joined by plywood splices fully glued on the surfaces in contact. The allowable shearing stress of the glue is 3.5 MPa, allowable tensile stress of the wood is 5.50 MPa and allowable bearing stress of the wood is 8 MPa. From the figure: B = 125 mm gap, t = 6mm L = 150mm Thickness of wood 1 and 3 = 40mm Thickness of wood 2 = 100mm Determine the maximum load P that can be carried by the 40mm wood.
A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positions indicated. 3 m 2.5 m C 1200 kN 900 kN 80mmØ 100mmØ E = 83 GPa Bronze E = 200 GPa Steel Which of the following most nearly gives the deformation of C? a. -0.7855 mm О Ъ. +0.8575 mm c. +0.7855 mm o d. - о.8575 mm
In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1245psi for the plywood and 725psi for the boards. The working shear stress for the glue is 52psi. Determine the dimension b so that the joint is as strong as the boards.____________inches in 2 decimal places.
The wooden members A and B are to be joined by plywood splice plates that will be fully glued on the surfaces in contact. The clearance between the ends of the members is to be 11 mm, the length of the plywood is L = 288 mm and the width of the wood is W = 119 mm. Find the shearing stress (in Mpa) in the glue if P = 35.9 kN. Round off the final answer to two decimal places.
A wood beam reinforced by an aluminum channel section is shown in the figure. 150 mm 232 mm 38 mm 6.5 mm 163 mm- The beam has a cross section of dimensions 150 mm x 232 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 MPa and 46 MPa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam? Enter the magnitude in kN • m. (Assume that the component parts of the beam are securely bonded by adhesives or connected by fasteners. Also, be sure to use the transformed-section method in the solution.) kN m
A wood beam reinforced by an aluminum channel section is shown in the figure. 150 mm 230 mm 38 mm 6.5 mm -163 mm- The beam has a cross section of dimensions 150 mm x 230 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 MPa and 50 MPa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam? Enter the magnitude in kN · m. (Assume that the component parts of the beam are securely bonded by adhesives or connected by fasteners. Also, be sure to use the transformed-section method in the solution.) (No Response) 14.06 kN· m
Question. Two plates each of 50 mm x 500 mm section are glued together along the length to form a section 50 mm x 1000 mm, used as a beam. If the shear force at a section is 1000 N. What is the maximum shear stress on the glue?