problem: In the tollowing Figures, Find the force torque at the given paints. 200 N Loo N 200 N EMA EMga? EMe=? 2. 2 B Figure! 50N 500lb 40olb 135° EMA EMB= 44 2001b A 2 5m C 300 N 1 2m EM%3= EMcz?

Q: On the attached drawing 11A005< what is dimension "G"

A:

Q: In a band brake, the diameter of the drum is 8 inches, and the angle of wrap is 210 degree. With a…

A:

Q: The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100…

A:

Q: n= 7

A: Kindly refer attachment for detailed answer.

Q: =o7 Cm) findSmax. tor Figure 0,7 Cm) fin mox. tor tigure tigure. 225 mm J0omm

A: Given Data The force acting in the downward direction is: F=400 N The height of the weld is: h=0.7…

Q: Determine the hT tyre height  and diameter D for the following tyres: a) 480/65R46 155 A8 b)…

A: The objective of the question is to calculate the tyre height and diameter for the given tyres. The…

Q: The Boss is created at 59.88, what is the allowed Position Tolerance?

A: Given data as per question Basic size of the boss =60

Q: A RWD Formula SAE car is given with the following information m = 600 lbm (including the driver), l=…

A:

Q: Q3. Design (draw) Inspection gauges for inner diameter of holes and outer diameter of shafts.…

A: Given: Shaft and hole tolerances To Find: Go and No go gauges

Q: a)Draw the normal force diagram. b)Draw the shear force diagram. c)Draw the bending moment diagram

A:

Q: N Mi4 D 3- O 314 2 314 DIA, C'BOREX DE 2 HOLES

A: Given Data : 2D Drawing

Q: 5 Answer the following: a) Briefly describe the difference between a bias ply and radial tyre. b)…

A: 5 a)Bias Ply Tyre Construction:-Bias ply tyres are made with reinforcing cord which is laid out…

Q: Use the following values in this exercise. Use an elastic approach in the calculations.N = 600 kNV =…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts,…

Q: Calculate the value of fx and fy 240 200N

A: As per given  We have to find fx and fy

Q: E

A: Computer aided drawing is the way to draw the various views of the component. The orthogonal view,…

Q: Why Fsin40= 80*9.8 how can I know is Fsin40

A: Given Data

Q: Determine which rigid body experiences complex motion Locate the instant center for that rigid body…

A:

Q: R20 R28 XL 296

A: Given: Draw the front, Side and top

Q: ។ 2 KN G lom 10KN-M B 6m 8m IKN ях find torque about AB

A: Given DataP=2kNPo=1kNM=10kNm

Q: Metrology Discuss both figures and explain which one comply with Taylor principle and why?

A: Taylor's principle in metrology says that the GO gauge should check all the dimensions of the…

Q: 5. Use superposition to find the deflection of the free end of the cantilever shown below: w lb/ft 2…

A:

Q: What are the forces cx and cy? Force F = 150

A: Given data F=150lb

Q: 1) x (squre> mm 2) (squre> x (trinngle) *) y ctriangle ) :9 3) mm mm 5) all area mm? 1) all area 7)…

A:

Q: AB beam is a W section drawn profile, P= 50 kN, L= 1,25 m ve E= 200 GPa since it is ( Iw= 26,9.106…

A:

Q: Find the force in member EC? 30% 6 ft B 300 lb 6 ft 300 lb 30° -6 ft

A: A plane truss given

Q: 6KNim 4kN/m What is the concentrated load of the rectangular loading as shown in the figure? 6 KN…

A: It is required to determine concentrated load of rectangular and triangular loading

Q: 1- What are the Lachrange equations for the particle in the given figure? A) L=mR-0² – mgRcos0 B) L=…

A:

Q: Orthogonal cutting, in a machining process, The attacking team sawdust (α) is 10 ̊. operation chip…

A:

Q: Angle of Twist Degrees Stress (Mpa) Torque (Nm) 0.4% Carbon Steel 1 2 Revs Radians 0.4% Carbon Steel…

A: Given data: - The angle of twist in first observation is θ1D = 0.3o. The angle of twist in second…

Q: Units are IPS. Just need a general direction on which sketches to make first, which extrusions to…

A: Find Draw the given object step by step.

Q: 2 2XRO 16 0.9 + 2.7 -2.2- -0.7-1 -1.25- ~IB 06 1.4 2,9 09 -1.6- SCALE: 1=1 SCALE: 1=2

A: Just mark all necessary dimension lines.

Q: 12 Find maX. W=? if of530Mpa Ś GoMpa い Joomm 2m An 30 そaん 500

A: Stress When body is subjected to any load then body resist that load and the resistance is called as…

Q: B) Could the following matrix represent a Stiffness Matrix? 1 -1 -1 -5 121. Yes No

A:

Q: What is the overall capacity for the question in the image

A: Bottlenecks are those process which slows the production  Let the total number of units taken for…

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. A = 3.55 B…

A:

Q: m (kg) F1 (N) r1(m) m2(Kg) F2 (N) R2 (m) T 1 T2 Tnet (N.m) 15*9.81 *9.81 (N.m) (N.m) 15 147.15 0.25…

A: Whenever we apply force on a body and the body starts rotating about a certain axis the that force…

Q: If the element is rotated by 60 degree 20 MPa 50 MPa -40.0 50.00 40 00 -30.00 -20.00 10,00 -7.016…

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.